Information pump assy, fuel fe
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
IMIFAFTAbT Oil pump assembly ND094200-0251 094200-0251 Fits for HP0 Fuel Injection Pump ND0942000251 0942000251
IMIFAFTAbT Product Name: ND094200-0251 094200-0251 ND0942000251 0942000251 Oil pump assembly || Part number: ND094200-0251 094200-0251 ND0942000251 0942000251 || Fits for HP0 Fuel Injection Pump || 1 PCS Oil pump assembly || Note: Please confirm that the product shown in the part number is what you need. If you cannot confirm you can leave us a message and provide your engine serial number and nameplate
IMIFAFTAbT Product Name: ND094200-0251 094200-0251 ND0942000251 0942000251 Oil pump assembly || Part number: ND094200-0251 094200-0251 ND0942000251 0942000251 || Fits for HP0 Fuel Injection Pump || 1 PCS Oil pump assembly || Note: Please confirm that the product shown in the part number is what you need. If you cannot confirm you can leave us a message and provide your engine serial number and nameplate
Scheme ###:
| 000. | [01] | 09420-00251 | PUMP ASSY, FUEL FE | |
| 001. | [01] | 09421-00070 | HOUSING SUB-ASSY, | |
| 002. | [01] | 09423-10050 | CASING, FEED PUMP | |
| 003. | [01] | 09423-00040 | PUMP SUB-ASSY, FUE | |
| 004. | [01] | 09424-10040 | PLATE, FEED PUMP S | |
| 005. | [01] | 09424-40040 | PLATE, FEED PUMP S | |
| 006. | [01] | 09425-10050 | COVER, FEED PUMP | |
| 007. | [04] | 09408-20040 | SCREW, SUPPLY PUMP | |
| 008. | [01] | 09408-60200 | O-RING, SUPPLY PUM | |
| 009. | [01] | 09408-70050 | SEAL, SUPPLY PUMP | |
| 010. | [01] | 09420-50030 | KEY | |
| 010. | [01] | 09420-50060 | KEY | |
| 011. | [02] | 09212-40010 | SPRING, FEED PUMP | 09212-40010 |
| 012. | [02] | 09212-10011 | VALVE, FEED PUMP C | 09212-10010 |
| 013. | [01] | 09212-60010 | PLUG, FEED PUMP CH | 09212-60010 |
| 014. | [01] | 09213-00360 | PUMP SUB-ASSY, PRI | |
| 015. | [02] | 09212-50010 | GASKET, CHECK VALV | 09212-50010 |
| 016. | [02] | 09031-70060 | PLUG, SCREW | |
| 017. | [02] | 94901-81500 | WASHER, COPPER PLA | |
| 018. | [04] | 94904-43320 | BOLT | |
| 019. | [06] | 09022-20070 | WASHER, FUEL PIPE | 09022-20070 |
| 020. | [01] | 09031-00490 | VALVE ASSY, OVERFL | |
| 022. | [01] | 09222-00040 | FILTER, FEED PUMP | 09222-00040 |
| 023. | [01] | 09222-30042 | SCREW, FUEL PIPE H |
Include in #3:
09400-00320
as PUMP ASSY, FUEL FE
09420-00251
Cross reference number
| Part num | Firm num | Firm | Name |
| 09420-00251 | PUMP ASSY, FUEL FE |
Information:
The impeller shaft nut is a left hand thread (CCW).
(5) Install the compressor wheel (at room temperature) as follows: a. Put compressor wheel on the shaft.b. Put a small amount of clean engine oil on the threads.c. Tighten the nut (CCW) to 14 to 17 N m (125 to 150 lb in).d. Loosen the nut and tighten again to 9 N m (80 lb in) plus an additional 60 degrees (1/6 turn).
Do not bend or add stress to the shaft when the nut is loosened or tightened.
(6) Thickness of each thrust ring ... 2.553 0.013 mm (.1005 .0005 in)(7) Bore in housing (new) ... 20.744 to 20.757 mm (.8167 to .8172 in) Outside diameter of the bearing (new) ... 20.630 to 20.643 mm (.8122 to .8127 in)Maximum permissible clearance between bearing and bore in housing (worn) ... 0.15 mm (.006 in)Torque for four nuts (put 5P3931 Anti-Seize Compound on threads) and bolts that hold turbocharger to exhaust manifold ... 55 5 N m (40 4 lb ft)Install the band clamps to hold the cartridge to the compressor housing as follows: a. Tighten clamps to 14 1.1 N m (125 10 lb in)b. Tap (hit) clamp lightly all around.c. Tighten again to ... 14 1.1 N m (125 10 lb in) Put clean engine oil in the oil inlet of the turbocharger after assembly or before installation to provide start up lubrication and/or storage protection.