Fuel injectors
  1. Home
  2. denso
  3. #09420-00071

09420-00071 PUMP ASSY, FUEL FE Denso Cross


 

Information pump assy, fuel fe

09420-00071 PUMP ASSY, FUEL FE
Rating:
78
Buy PUMP ASSY, FUEL FE 09420-00071 genuine, new aftermarket engine parts with delivery

Scheme ###:

PUMP ASSY, FUEL FE
000. [01] 09420-00071 PUMP ASSY, FUEL FE
001. [01] 09421-00070 HOUSING SUB-ASSY,
002. [01] 09423-10050 CASING, FEED PUMP
003. [01] 09423-00040 PUMP SUB-ASSY, FUE
004. [01] 09424-10040 PLATE, FEED PUMP S
005. [01] 09424-40040 PLATE, FEED PUMP S
006. [01] 09425-10050 COVER, FEED PUMP
007. [04] 09408-20040 SCREW, SUPPLY PUMP
008. [01] 09408-60200 O-RING, SUPPLY PUM
009. [01] 09408-70050 SEAL, SUPPLY PUMP
010. [01] 09420-50030 KEY
010. [01] 09420-50060 KEY
011. [02] 09212-40010 SPRING, FEED PUMP S2256-21020-A
012. [02] 09212-10011 VALVE, FEED PUMP C S2256-31041-A
013. [01] 09212-60010 PLUG, FEED PUMP CH S2284-51350-A
014. [01] 09213-00450 PUMP SUB-ASSY, PRI S2250-91400-A
014-001. [01] 09211-70102 CONNECTOR
014-002. [01] 09212-50010 GASKET, CHECK VALV S2284-71680-A
014-003. [01] 09213-00360 PUMP SUB-ASSY, PRI S2250-91370-A
015. [03] 09212-50010 GASKET, CHECK VALV S2284-71680-A
016. [02] 09031-70060 PLUG, SCREW S2284-51060-A
017. [02] 94901-81500 WASHER, COPPER PLA S2284-71120-A
018. [04] 94904-43320 BOLT S2281-52070-A
019. [04] 94901-02490 WASHER S2287-71100-A
020. [01] 94918-00310 SCREW, HOLLOW S2283-51310-A
022. [01] 09216-00020 HOLDER SUB-ASSY, V S2281-52600-A
023. [01] 09222-00040 FILTER, FEED PUMP S2257-41040-A
024. [01] 09222-30070 SCREW, FUEL PIPE H S2283-51370-A

Include in #3:

09400-00125 as PUMP ASSY, FUEL FE
09420-00071

Cross reference number



Part num Firm num Firm Name
09420-00071    PUMP ASSY, FUEL FE




Information:

Remove Timing Gears
Start By:a. remove timing gear case cover1. Put the No. 1 piston at top dead center on the compression stroke. Be sure all the timing marks are in alignment with each other. 2. Remove plate (2) that holds idler gear (1). 3. Remove idler gear (1). 4. Inspect two bushings (3) in idler gear (1). See Engine Specifications for bushing diameter. Remove two bushings (3) if replacement is necessary. 5. Remove fuel injection pump drive gear (4). 6. Bend lock (5) away from the bolt. Remove the bolt and remove washer (6). 7. Remove camshaft drive gear (7) with tool (A).Install Timing Gears
1. Align the slot in gear (1) with the key in the camshaft. Put the camshaft gear in position on the camshaft. 2. Install washer (2), lock (3) and the bolt. Tighten the bolt to a torque of 60-70 N m (45-52 lb ft). Bend the tab of the lock against the bolt head. 3. Align the roll pin in fuel injection pump drive gear (4) with the hole in fuel injection pump drive shaft (5). Install fuel injection pump drive gear (4) on to fuel injection pump drive shaft (5). 4. Install three bolts (6) to hold drive gear (4) to the fuel injection pump drive shaft. 5. Use tool (A) to install two bushings (7) into idler gear (8). Install the bushings even with the outside of idler gear (8). 6. Align the timing marks on idler gear (8) with the crankshaft gear, camshaft drive gear and the fuel injection pump drive gear. 7. Install plate (9) and the bolts to hold idler gear (8) on the idler gear shaft. Tighten the three bolts to a torque of 40 N m (30 lb ft). 8. Check the idler gear end clearance. The clearance must be at least 0.25 mm (.010 in). 9. Fasten a steel plate to the timing gear case. Fasten tooling (A) to the plate as shown. Check the timing gear backlash. The backlash must be 0.08 - 0.15 mm (.003 - .006 in).

Have questions with 09420-00071?





09420-00064 PUMP ASSY, FUEL FE 09420-00062 09420-00040 09420-00030 09420-00021
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09420-00071

Back to top