09350-06780 HOLDER & NOZZLE SE Denso Cross


 

Information holder & nozzle se

09350-06780 HOLDER & NOZZLE SE
Rating:
19
Buy HOLDER & NOZZLE SE 09350-06780 genuine, new aftermarket engine parts with delivery

Components :

001. HOLDER & NOZZLE SE 09350-06780

Scheme ###:

000. [01] 09350-06780 HOLDER & NOZZLE SE ME072848
001. [01] 09310-06780 HOLDER ASSY, NOZZL ME743160
001-001. [01] 09311-06780 BODY SUB-ASSY, NOZ ME743352
001-002. [01] 09312-10330 PIN, NOZZLE HOLDER ME703615
001-003. [01] 09312-70270 SPRING, NOZZLE HOL ME703616
001-004. [01] 09313-10200 SCREW, ADJUST ME703617
001-005. [01] 09313-40150 NUT, CAP ME022310
001-005. [01] 09313-40290 NUT, CAP ME703618
001-006. [01] 09315-10500 CONNECTOR, NOZZLE ME728816
001-007. [01] 09315-80010 GASKET, INLET CONN MM500889
001-008. [01] 09316-41400 NUT, NOZZLE RETAIN ME728359
001-009. [01] 09316-60091 SCREW, HOLLOW ME703657
001-010. [01] 09324-50052 WASHER MM501731
001-011. [02] 94901-81020 WASHER, COPPER PLA ME022309
002. [01] 09340-03130 NOZZLE ASSY ME743161

Include in #3:

09350-06780 as HOLDER & NOZZLE SE

Include as Nozzle:

Cross reference number



Part num Firm num Firm Name
09350-06780  ME072848  HOLDER & NOZZLE SE
ME072848    MITSUBISHI HOLDER & NOZZLE SE




Information:

3500 Family EnginesIntroduction
1. Type 2 fuel injector. 2. Two piece follower. 3. Nose cone. 4. Nozzle assembly.Tools are now available for the removal and installation of nose cone (3), on type 2 fuel injectors (1), when it is necessary to replace a nozzle assembly (4). Type 2 fuel injectors can be identified by the two piece follower (2).
5. 1U9395 Plate. 6. 1U8701 Socket.Use 1U9395 Plate (5) with the 6V4830 Fixture Group (not shown) and the procedure given in this instruction, for the removal and installation of nozzle assembly (4).Earlier type 2 injectors have a nose cone that has serrations on its exterior. These serrations will be damaged when the nose cone is removed. A damaged nose cone is not to be used again. A 7C9795 Nose Cone is available for use as a replacement for the original nose cone.The 7C9795 Nose Cone has a hexagon shape on its exterior. This nose cone can be installed and tightened using 1U8701 Socket (6). When the 7C9795 Nose Cone is installed, be sure to tighten it according to the procedure given in this instruction.Removal and Installation of Nose Cone and Nozzle Assembly
1. Remove the original plate from the 6V4830 Fixture Group and install 1U9395 Plate (1).2. Put injector (2) in position on the fixture group. If the exterior of the injector nose cone is a hexagon shape as shown at location (A), use the 1U8701 Socket for nose cone removal. 3. If the exterior of the nose cone has serrations as shown at location (B), use a pipe wrench, as shown, to remove the nose cone. Anytime a pipe wrench is used to remove a nose cone, the nose cone will be damaged. Never use or install a damaged nose cone on an injector. Always install a new 7C9795 Nose Cone as a replacement. 4. After the nose cone has been loosened, use a hammer and 6V4822 Tip Driver (3) to tap the nozzle assembly as shown. This is done to break the connection between the nozzle assembly and the nose cone. Be sure to use only the 6V4822 Tip Driver in this procedure, because use of a standard punch, or any other similar tool will cause damage to the nozzle tip.5. Remove the nose cone and nozzle assembly. 6. Inspect surface (C) in the injector. This is the sealing surface for the nozzle assembly. This surface must be clean and free of any scratches, nicks or burrs. Even a piece of lint from a shop towel can cause a leak and destroy nozzle performance. 7. Remove original O-ring seal (4). Install a new O-ring seal, refer to the Parts Book for the correct part number. Make sure the O-ring seal is not damaged during installation.Use a generous amount of 1P0808 Grease, or a good grade of multi-purpose lubricant, to lubricate the O-ring seal before the nose cone is installed.8. Install new nozzle assembly (5) on the injector. 9. Install and finger tighten the new 7C9795 Nose Cone on the injector.

Have questions with 09350-06780?





Group cross 09350-06780

Back to top