Information holder & nozzle se
Rating:
Components :
| 001. | HOLDER & NOZZLE SE | 09350-05691 |
| 001. | HOLDER & NOZZLE SE | 09350-05691 |
Scheme ###:
| 000. | [01] | 09350-05691 | HOLDER & NOZZLE SE | 23610-2001 |
| 000. | [01] | 09350-05691 | HOLDER & NOZZLE SE | S2361-02001 |
| 001. | [01] | 09310-05691 | HOLDER ASSY, NOZZL | S2363-01930-B |
| 001-001. | [01] | 09311-05691 | BODY SUB-ASSY, NOZ | |
| 001-002. | [01] | 09312-10580 | PIN, NOZZLE HOLDER | |
| 001-003. | [01] | 09312-70280 | SPRING, NOZZLE HOL | S2361-51190-A |
| 001-004. | [01] | 09312-80100 | SEAT, SPRING | |
| 001-005. | [01] | 09312-90150 | SCREW, CAP | |
| 001-006. | [01] | 09313-30100 | GASKET | S2366-11150-A |
| 001-007. | [01] | 09313-40191 | NUT, CAP | |
| 001-008. | [01] | 09315-10290 | CONNECTOR, NOZZLE | S2360-11130-A |
| 001-009. | [01] | 09315-80010 | GASKET, INLET CONN | S2362-11070-A |
| 001-010. | [01] | 09316-41590 | NUT, NOZZLE RETAIN | |
| 001-011. | [01] | 09322-00120 | PACKING SUB-ASSY, | S2361-71620-A |
| 001-012. | [01] | 94918-00630 | SCREW, HOLLOW | S2283-51130-A |
| 001-012. | [01] | 09507-40012 | SCREW, HOLLOW OUTL | S2283-51570-A |
| 001-014. | [02] | 94901-02640 | WASHER | S2284-71870-A |
| 002. | [01] | 09340-02880 | NOZZLE ASSY | S2365-01821-A |
Include in #3:
09350-05691
as HOLDER & NOZZLE SE
09350-05691
Cross reference number
| Part num | Firm num | Firm | Name |
| 09350-05691 | 23610-2001 | HOLDER & NOZZLE SE |
Information:
Introduction
The problem that is identified below has a known solution. Use the solution that is identified below.Problem
The procedure for the Disassembly and Assembly needs to be updated to include the information below.Solution
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
Inspect the quill tubes and fuel injectors for cuts or marks at the mating surfaces.
Replace any quill tubes since the quill tubes are a one time use component. Replace the copper washer when replacing the fuel injector.
Follow the steps below for installing the quill tunes and fuel injectors.
Seat the injector by installing and torquing the injector hold down clamp bolt to 30 3 N m (22 2 lb ft).
Install the quill tube and tighten the quill nut between 15 N m (11 lb ft) to 20 N m (15 lb ft).
Apply a final torque of 30 3 N m (22 2 lb ft) to the injector hold down clamp bolt.
Apply a final torque between 50 N m (37 lb ft) to 55 N m (41 lb ft).
The problem that is identified below has a known solution. Use the solution that is identified below.Problem
The procedure for the Disassembly and Assembly needs to be updated to include the information below.Solution
Do not operate or work on this product unless you have read and understood the instruction and warnings in the relevant Operation and Maintenance Manuals and relevant service literature. Failure to follow the instructions or heed the warnings could result in injury or death. Proper care is your responsibility.
Inspect the quill tubes and fuel injectors for cuts or marks at the mating surfaces.
Replace any quill tubes since the quill tubes are a one time use component. Replace the copper washer when replacing the fuel injector.
Follow the steps below for installing the quill tunes and fuel injectors.
Seat the injector by installing and torquing the injector hold down clamp bolt to 30 3 N m (22 2 lb ft).
Install the quill tube and tighten the quill nut between 15 N m (11 lb ft) to 20 N m (15 lb ft).
Apply a final torque of 30 3 N m (22 2 lb ft) to the injector hold down clamp bolt.
Apply a final torque between 50 N m (37 lb ft) to 55 N m (41 lb ft).