Information holder & nozzle se
Rating:
Components :
| 001. | HOLDER & NOZZLE SE | 09350-04850 |
| 001. | HOLDER & NOZZLE SE | 09350-04850 |
Scheme ###:
| 000. | [01] | 09350-04850 | HOLDER & NOZZLE SE | 23610-1780 |
| 000. | [01] | 09350-04850 | HOLDER & NOZZLE SE | S2361-01780 |
| 001. | [01] | 09310-04850 | HOLDER ASSY, NOZZL | S2363-01710-A |
| 001-001. | [01] | 09311-04850 | BODY SUB-ASSY, NOZ | S2360-21310-A |
| 001-002. | [01] | 09312-10330 | PIN, NOZZLE HOLDER | S2361-61030-A |
| 001-003. | [01] | 09312-70280 | SPRING, NOZZLE HOL | S2361-51190-A |
| 001-004. | [01] | 09313-10200 | SCREW, ADJUST | S2361-41060-A |
| 001-005. | [01] | 09313-40270 | NUT, CAP | S2362-31310-A |
| 001-006. | [01] | 09315-10340 | CONNECTOR, NOZZLE | 23611-1190A |
| 001-007. | [01] | 09315-80010 | GASKET, INLET CONN | S2362-11070-A |
| 001-008. | [01] | 09316-40940 | NUT, NOZZLE RETAIN | S2363-31190-A |
| 001-009. | [01] | 94918-00630 | SCREW, HOLLOW | S2283-51130-A |
| 001-009. | [01] | 09507-40012 | SCREW, HOLLOW OUTL | S2283-51570-A |
| 001-010. | [01] | 09324-50052 | WASHER | S2284-71290-A |
| 001-011. | [02] | 94901-02640 | WASHER | S2284-71870-A |
| 002. | [01] | 09340-02520 | NOZZLE ASSY | S2365-01690-A |
Include in #3:
09350-04850
as HOLDER & NOZZLE SE
09350-04850
Include as Nozzle:
Cross reference number
| Part num | Firm num | Firm | Name |
| 09350-04850 | 23610-1780 | HOLDER & NOZZLE SE | |
| 23610-1780 | HINO | HOLDER & NOZZLE SE | |
| S2361-01780 | HINO | HOLDER & NOZZLE SE |
Information:
Choose the appropriate drive for your monitor from the table below. The 203-7811 Engine Monitoring Control Group uses Wonderware as the "Graphic Display Application". The 203-7810 Engine Monitoring Control Group uses RSView as the "Graphic Display Application".
Table 1
Drive "Graphic Display Application"
203-7816 Storage Drive RSView
204-8792 Storage Drive Wonderware In order to install the drive, perform the procedure that follows:
Connect the ribbon cable connector and power cables to the hard drive and the floppy disk drive.Note: Make sure that the ribbon cable is correctly installed. The connector must be positioned so that the red wire of the cable is closest to the back of the unit. If you are using the new cables, also connect the other end of the cables to the Central Processing Unit (CPU) card.
Illustration 1 g00858453
(1) Drive Bay Mounting Studs
Position the drive bay into the chassis so that the studs (1) on the chassis fit into the grommets on the drive bay.Note: Be careful not to push the vibration dampers (grommets) on the drive bay out of the sheet metal.
Install the back cover.
Apply power and verify the operation of the drive. Refer to any additional instructions that are provided with the drive.
Table 1
Drive "Graphic Display Application"
203-7816 Storage Drive RSView
204-8792 Storage Drive Wonderware In order to install the drive, perform the procedure that follows:
Connect the ribbon cable connector and power cables to the hard drive and the floppy disk drive.Note: Make sure that the ribbon cable is correctly installed. The connector must be positioned so that the red wire of the cable is closest to the back of the unit. If you are using the new cables, also connect the other end of the cables to the Central Processing Unit (CPU) card.
Illustration 1 g00858453
(1) Drive Bay Mounting Studs
Position the drive bay into the chassis so that the studs (1) on the chassis fit into the grommets on the drive bay.Note: Be careful not to push the vibration dampers (grommets) on the drive bay out of the sheet metal.
Install the back cover.
Apply power and verify the operation of the drive. Refer to any additional instructions that are provided with the drive.