09350-02290 HOLDER & NOZZLE SE Denso Cross


 

Information holder & nozzle se

09350-02290 HOLDER & NOZZLE SE
Rating:
75
Buy HOLDER & NOZZLE SE 09350-02290 genuine, new aftermarket engine parts with delivery

Components :

001. HOLDER & NOZZLE SE 09350-02290

Scheme ###:

000. [01] 09350-02290 HOLDER & NOZZLE SE 10627-01200
001. [01] 09310-02290 HOLDER ASSY, NOZZL 10627-11300
001-001. [01] 09311-02290 BODY SUB-ASSY, NOZ
001-002. [01] 09312-10330 PIN, NOZZLE HOLDER
001-003. [01] 09312-70270 SPRING, NOZZLE HOL
001-004. [01] 09313-10200 SCREW, ADJUST
001-005. [01] 09313-40290 NUT, CAP
001-006. [01] 09315-10280 CONNECTOR, NOZZLE
001-007. [01] 09315-80010 GASKET, INLET CONN 14301-53381
001-008. [01] 09316-40781 NUT, NOZZLE RETAIN
001-009. [01] 94918-00152 SCREW, HOLLOW
001-010. [01] 09324-50052 WASHER
001-011. [02] 94901-81020 WASHER, COPPER PLA 15221-96661
002. [01] 09340-01320 NOZZLE ASSY 10627-12500

Include in #3:

09350-02290 as HOLDER & NOZZLE SE

Include as Nozzle:

Cross reference number



Part num Firm num Firm Name
09350-02290  10627-0120  HOLDER & NOZZLE SE
10627-01200    KUBOTA HOLDER & NOZZLE SE




Information:

General Hazard Information
Attach a DO NOT OPERATE or similar warning tag to start switch or controls before performing maintenance or repairing the engine. These tags, SEHS7332, are available from your Caterpillar dealer. When appropriate, attach tags at the engine and at each start position and disconnect starting controls.Do not allow unauthorized personnel on or around the engine when it is being serviced.Diesel engine exhaust contains products of combustion which may be harmful to your health. Always start and operate the engine in a well ventilated area and, if in an enclosed area, vent the exhaust to the outside.Use caution when removing cover plates. Gradually loosen (do not remove) the last two bolts or nuts located at opposite ends of the cover or device. Pry cover loose to relieve any spring or other pressure, before removing the last bolts or nuts.Use caution when removing vent release valve, grease fittings, pressure taps, breathers or drain plugs. Hold a rag over the cap or plug to prevent being sprayed or splashed by liquids under pressure.* Wear a hard hat, protective glasses, hearing protection and other protective equipment as required by job conditions.* Do not wear loose clothing or jewelry that can catch on controls or other parts of the engine.* Make certain all protective guards and covers are secured in place.* Use all cleaning solutions with care.* Never put maintenance fluids into glass containers since glass containers can break.* Report all needed repairs.* Stop the engine.* Do not attempt any repairs or adjustments to the engine or driven equipment while it is running.* Do not attempt repairs you do not understand.* Ensure the protective locks or controls are in the applied position.* Be sure the remote starting system is inoperative on the equipment being serviced. Always disconnect the engine starter circuit when working on the generator. Place the automatic start-stop switch to the STOP position before working on the equipment to prevent accidental starting.* Disconnect the batteries whenever performing any maintenance or before servicing the electrical system. If the engine has electric starters, disconnect and tape the battery ground leads to prevent accidental starting.* Use proper tools; replace or repair broken or damaged equipment.* When starting an engine after repairs have been made to the fuel system or governor, make provisions for shutting off the engine's intake air and/or fuel supply (to stop the engine), in case there is an overspeed on start-up.Pressure Air and Water
Pressure air can cause personal injury. When using pressure air for cleaning, wear a protective face shield, protective clothing and protective shoes.The maximum air pressure must be below 200 kPa (30 psi) for cleaning purposes.Wear eye protection at all times when cleaning the cooling system. Pressurized water could cause debris and/or hot water to be blown and result in personal injury.Fluid Penetration
Always use a board or cardboard when checking for a leak. Escaping fluid under pressure, even a pin-hole size leak, can penetrate body tissue, causing serious injury or possible death.If fluid is injected into your

Have questions with 09350-02290?





Group cross 09350-02290

Back to top