Information holder & nozzle se
Rating:
Components :
| 001. | HOLDER & NOZZLE SE | 09350-01441 |
Scheme ###:
| 000. | [01] | 09350-01441 | HOLDER & NOZZLE SE | EZ01441 |
| 001. | [01] | 09310-01441 | HOLDER ASSY, NOZZL | |
| 001-001. | [01] | 09311-11441 | BODY | |
| 001-002. | [01] | 09312-10030 | PIN, NOZZLE HOLDER | 09312-10030 |
| 001-003. | [01] | 09312-70020 | SPRING, NOZZLE HOL | 09312-70020 |
| 001-004. | [01] | 09315-00130 | CONNECTOR SUB-ASSY | EZ0087404 |
| 001-005. | [01] | 09315-80010 | GASKET, INLET CONN | EZ0087405 |
| 001-006. | [01] | 09316-40741 | NUT, NOZZLE RETAIN | EZ41012002 |
| 001-007. | [01] | 09326-60041 | FLANGE | EZ41012003 |
| 001-008. | [01] | 09313-10130 | SCREW, ADJUST | EZ0087408 |
| 001-009. | [01] | 09313-40150 | NUT, CAP | 09313-40150 |
| 001-010. | [01] | 09324-50052 | WASHER | ME022312 |
| 001-011. | [01] | 94918-00152 | SCREW, HOLLOW | 00918-00152 |
| 001-012. | [02] | 94901-81020 | WASHER, COPPER PLA | 94901-81020 |
| 002. | [01] | 09340-00200 | NOZZLE ASSY | EZ00879 |
Include in #3:
09350-01441
as HOLDER & NOZZLE SE
Cross reference number
| Part num | Firm num | Firm | Name |
| 09350-01441 | EZ01441 | HOLDER & NOZZLE SE |
Information:
Possible Causes/Corrections
Minor Operating Faults/To help identify a problem before a more involved troubleshooting procedure is started, follow the procedure given in the PRIMARY ENGINE CHECKS section. Fuel Ratio Control Out of Adjustment or Bad/Follow the procedure in the Testing and Adjusting section of this Service Manual. Check Engine Performance/Do a Power Analysis report (PAR), Level II, to check engine performance. See Special Instruction, Form No. SEHS8025 and SEHS7886 for the tooling and procedures to use. Be sure to make a record of the temperatures for inlet air, fuel (at filter base), lubricating oil and coolant. Fuel Settings Not Correct/If the Power Analysis Report indicates a problem, the governor fuel settings should be verified. See the Testing and Adjusting section of this Service Manual for the necessary procedures. Also, refer back to the information learned earlier (see OWNER/OPERATOR INPUT section) about the truck specifications and application and judge whether or not the engine is performing as expected or customer expectation is realistic. Bad Fuel Nozzle(s)/Remove the fuel nozzles and test as in the Testing and Adjusting section of this Service Manual.Recommended Procedure Without Chassis Dynamometer
Possible Causes/Corrections
Minor Operating Faults/To help identify a problem before a more involved troubleshooting procedure is started, follow the procedure given in the PRIMARY ENGINE CHECKS section. Fuel Ratio Control Out of Adjustment or Bad/Follow the procedure in the Testing and Adjusting section of this Service Manual. Fuel Injection Timing Not Correct/Follow the procedures in the Testing and Adjusting section of this Service Manual. Check Engine Performance/Install the tooling and follow the procedure given in the ROAD TEST section. Fuel Settings Not Correct/If the Road Test indicates a problem, the governor fuel settings should be verified. See the Testing and Adjusting section of this Service Manual for the necessary procedures. Also, refer back to the information learned earlier (see OWNER/OPERATOR INPUT section) about the truck specifications and application and judge whether or not the engine is performing as expected or customer expectation is realistic. Any Further Diagnosis Must Be Done On A Chassis Dynamometer/If the fuel settings are correct and the above procedures have been followed without finding the problem a Power Analysis Report (PAR), Level II, must be done on the engine. See Special Instruction, Form Nos. SEHS8025 and SEHS7886 for the correct tools and procedures to use.
Minor Operating Faults/To help identify a problem before a more involved troubleshooting procedure is started, follow the procedure given in the PRIMARY ENGINE CHECKS section. Fuel Ratio Control Out of Adjustment or Bad/Follow the procedure in the Testing and Adjusting section of this Service Manual. Check Engine Performance/Do a Power Analysis report (PAR), Level II, to check engine performance. See Special Instruction, Form No. SEHS8025 and SEHS7886 for the tooling and procedures to use. Be sure to make a record of the temperatures for inlet air, fuel (at filter base), lubricating oil and coolant. Fuel Settings Not Correct/If the Power Analysis Report indicates a problem, the governor fuel settings should be verified. See the Testing and Adjusting section of this Service Manual for the necessary procedures. Also, refer back to the information learned earlier (see OWNER/OPERATOR INPUT section) about the truck specifications and application and judge whether or not the engine is performing as expected or customer expectation is realistic. Bad Fuel Nozzle(s)/Remove the fuel nozzles and test as in the Testing and Adjusting section of this Service Manual.Recommended Procedure Without Chassis Dynamometer
Possible Causes/Corrections
Minor Operating Faults/To help identify a problem before a more involved troubleshooting procedure is started, follow the procedure given in the PRIMARY ENGINE CHECKS section. Fuel Ratio Control Out of Adjustment or Bad/Follow the procedure in the Testing and Adjusting section of this Service Manual. Fuel Injection Timing Not Correct/Follow the procedures in the Testing and Adjusting section of this Service Manual. Check Engine Performance/Install the tooling and follow the procedure given in the ROAD TEST section. Fuel Settings Not Correct/If the Road Test indicates a problem, the governor fuel settings should be verified. See the Testing and Adjusting section of this Service Manual for the necessary procedures. Also, refer back to the information learned earlier (see OWNER/OPERATOR INPUT section) about the truck specifications and application and judge whether or not the engine is performing as expected or customer expectation is realistic. Any Further Diagnosis Must Be Done On A Chassis Dynamometer/If the fuel settings are correct and the above procedures have been followed without finding the problem a Power Analysis Report (PAR), Level II, must be done on the engine. See Special Instruction, Form Nos. SEHS8025 and SEHS7886 for the correct tools and procedures to use.