09311-04770 BODY SUB-ASSY, NOZ Denso Cross


 

Information body sub-assy, noz

09311-04770 BODY SUB-ASSY, NOZ
Rating:
58
Buy BODY SUB-ASSY, NOZ 09311-04770 genuine, new aftermarket engine parts with delivery

Include in #3:

Number on scheme 001-001
BODY SUB-ASSY, NOZ
09350-04770 as BODY SUB-ASSY, NOZ

Cross reference number



Part num Firm num Firm Name
09311-04770  ME728872  BODY SUB-ASSY, NOZ
ME728872    MITSUBISHI BODY SUB-ASSY, NOZ




Information:

D3 (6N, 79U, 82U, 83U);
931 (8N, 10N, 78U, 81U);
910 (80U, 40Y, 41Y);
D3B (23Y, 24Y, 27Y, 28Y);
931B (25Y, 26Y, 29Y, 30Y) This information available on microfiche only.Reference: Service ManualThe 2W4387 Direct Injection Engine Arrangement, with the new scroll fuel system (NSFS), is the replacement engine for all D3, 910, 931 machines. This engine arrangement is a replacement for the former precombustion chamber diesel engine and the former direct injection diesel engine with an interium scroll fuel system (ISFS) that was used in earlier models of these machines.The new engine arrangement is also a replacement for all direct injection engines with a new scroll fuel system (NSFS) that have been used in D3B, 910, 931B machines. For D3B and 931B machines with NSFS and 3F-1R transmissions, the new engine arrangement is a direct replacement of the former engine arrangement. To install the new engine arrangement in other D3, 910, 931 machines, some parts must be removed from the new engine and different parts must be installed. Also some parts on the machine must be modified before installation of the new replacement engine.The information in this instruction is given by machine model, engine arrangement, and serial numbers. See the index that follows, and the chart on page 2. After the engine is installed in any of the machines above, and before engine start-up, always check the fuel setting dimension. See the Fuel Setting Information for the correct fuel setting dimension.Use chart that follows to find the serial numbers used with a specific type of machine. Installation Of 2W4387 Engine Arrangement In 910 Machines
Before installation of the 2W4387 Engine Arrangement, some changes must be made to the new engine and machine. See the information that follows. After engine installation is complete, adjust the fuel setting according to the dimension given in the FUEL SETTING INFORMATION. See the Service Manual for engine installation procedure.Oil Filler Tube
(1) Remove bolts (1), the washers, tube (2) and cap (3) from cover (4). (2) Use the former bolts (1) and washers to install 6N7401 Plate (5) and 6N7402 Gasket on cover (4). (3) Remove the 2P2772 Cover at location (A) on the side of the cylinder block. Use the bolts and washers from the 2P2772 Cover and a 4N933 Gasket to install 1W261 Tube Assembly (6) [in place of the 2P2772 cover] on cylinder block (7). Install 9L8439 Cap (8).Oil Level Gauge Group
(1) Remove the oil level gauge and guide from the cylinder block, and install 1W366 Oil Level Gauge Group (1). Governor Group
(1) Remove six bolts (1) and cover (2). (2) Remove snap rings (3) and plate (4). Hold governor shaft (5) in position while removing the cover and the plate. If the shaft is allowed to move out with the cover or plate, internal levers will come off of the shaft.(3) Remove spring (6) from the shaft assembly, and install a 8N3093 Spring in the same place. Do not remove shaft assembly as shown. The 8N3093 Spring has one blue stripe and former spring (6)

Have questions with 09311-04770?





Group cross 09311-04770

Back to top