09300-06461 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

09300-06461 PUMP ASSY, INJECTI
Rating:
15
Buy PUMP ASSY, INJECTI 09300-06461 genuine, new aftermarket engine parts with delivery

Scheme ###:

000. [01] 09300-06461 PUMP ASSY, INJECTI ME215110
001. [01] 19010-00550 BODY ASSY, INJECTI ME736498
002. [01] 09180-03603 TIMER ASSY, AUTOMA ME743439
003. [01] 09006-00451 COVER SUB-ASSY, TI ME736126
004. [01] 94914-02840 O-RING MH035502
005. [04] 94901-15020 WASHER, STEEL PLAT MH005068
006. [04] 90258-10001 WASHER, SPRING MC327716
007. [04] 91266-10081 NUT, HEXAGON MF430122
008. [01] 09130-05290 GOVERNOR ASSY, MEC ME736666
009. [01] 09210-02710 PUMP ASSY, FUEL FE ME728983
010. [01] 09028-50021 CAP ME035845
013. [01] 90458-04051 KEY, WOODRUFF ME728066
014. [01] 09001-20220 NUT, TIMER ROUND ME702033
015. [01] 09001-80090 COVER, CONTROL RAC ME702251
016. [05] 94904-72690 BOLT, W/WASHER ME702045
017. [01] 91418-06201 BOLT, W/WASHER ME702041
018. [01] 94904-73910 BOLT, W/WASHER ME703449
021. [01] 09028-50050 CAP ME076458
022. [01] 94901-40210 WASHER, COUNTERSUN ME702043

Include in #3:

09300-06461 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09300-06461  ME215110  PUMP ASSY, INJECTI




Information:

(1) Nut for impeller (See TURBOCHARGER IMPELLER INSTALLATION) Do not bend or add stress to the shaft when nut is tightened.(2) Torque for the bolts that hold the backplate ... 90 10 lb.in.(10 1 N m)(3) Torque for the clamp bolts ... 10 1 lb. ft.(14 1 N m)(4) Bore in the bearings ... .6268 to .6272 in.(15.921 to 15.931 mm) Diameter for the surfaces (journals) on the shaft for the bearings ... .6250 to .6254 in.(15.875 to 15.885 mm)(5) Bore in the housing ... .9827 to .9832 in.(24.961 to 24.973 mm) Outside diameter of the bearings ... .9782 to .9787 in.(24.846 to 24.859 mm)(6) Clearance between the ends of the oil seal ring ... .008 to .015 in.(0.20 to 0.38 mm)(7) End play for the shaft ... .003 to .010 in.(0.08 to 0.25 mm)(8) Torque for support nuts (put 9M3710 or 4S9416 Anti-Seize Compound on the stud threads) ... 40 4 lb. ft.(55 5 N m)(AiResearch T1810)
Make reference to ANALYZING TURBOCHARGER FAILURE. Form No. FEG45138.(1) End play for shaft ... .0065 .0025 in.(0.165 0.063 mm) Radial clearance for the shaft ... .004 to .009 in.(0.10 to 0.23 mm)(2) Bore in the bearing ... .6268 to .6272 in.(15.921 to 15.931 mm) Diameter of surface on shaft (journal) for the bearing ... .6250 to .6254 in.(15.875 to 15.885 mm)(3) Put 8S6747 Gasket Sealer on bolts holding compressor housing and tighten to ... 105 5 lb. in.(11.9 0.6 N m)(4) Put 9M3710 or 4S9416 Anti-Seize Compound on bolts holding turbine housing and tighten to ... 175 15 lb. in.(19.8 1.7 N m)(5) Put 9M3710 or 4S9416 Anti-Seize Compound on threads: Tighten bolts holding turbocharger to ... 40 4 lb. ft.(55 5 N m)(6) Nut for impeller (See TURBOCHARGER IMPELLER INSTALLATION). Do not bend or add stress to the shaft when nut is tightened.(7) Clearance between ends of oil seal ring (earlier) ... .001 to .006 in.(0.03 to 0.15 mm) Clearance between ends of oil seal ring (later) ... .008 to .015 in.(0.20 to 0.38 mm)(8) Torque for bolts holding thrust plate ... 35 5 lb. in.(4.0 0.6 N m)(9) Bore in housing ... .9827 to .9832 in.(24.961 to 24.973 mm) Outside diameter of the bearing ... .9780 to .9785 in.(24.841 to 24.854 mm)

Have questions with 09300-06461?





Group cross 09300-06461

Back to top