09300-06291 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

09300-06291 PUMP ASSY, INJECTI
Rating:
58
Buy PUMP ASSY, INJECTI 09300-06291 genuine, new aftermarket engine parts with delivery

Scheme ###:

000. [01] 09300-06291 PUMP ASSY, INJECTI ME215061
003. [01] 19010-00961 BODY ASSY, INJECTI ME736900
004. [01] 09130-05662 GOVERNOR ASSY, MEC ME736902
005. [01] 09180-03754 TIMER ASSY, AUTOMA ME736904
006. [01] 09210-02840 PUMP ASSY, FUEL FE ME736506
007. [01] 09006-00570 COVER SUB-ASSY, TI ME743445
008. [01] 94914-03690 O-RING ME736557
009. [01] 90458-05750 KEY, WOODRUFF ME702920
010. [01] 09001-20360 NUT, TIMER ROUND ME736909
011. [01] 94901-81550 WASHER, COPPER PLA ME039681
012. [01] 09001-80410 COVER, CONTROL RAC ME736558
013. [01] 09028-50021 CAP ME035845
014. [04] 94901-15020 WASHER, STEEL PLAT MH005068
015. [04] 90258-10001 WASHER, SPRING MC327716
016. [04] 91266-10081 NUT, HEXAGON MF430122
017. [02] 94904-76880 BOLT, W/WASHER ME728977
018. [01] 94904-76910 BOLT, W/WASHER ME728980
019. [01] 94904-76900 BOLT, W/WASHER ME728979
020. [04] 94904-76890 BOLT, W/WASHER ME728978
023. [01] 09028-50050 CAP ME076458

Include in #3:

09300-06291 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09300-06291  ME215061  PUMP ASSY, INJECTI




Information:

start by:a) remove flywheel 1. Use tool (A) to remove the crankshaft rear seal.2. Install tool (C) in the rear seal bore.
TYPICAL EXAMPLE3. Install tool (B) between tool (C) and the wear sleeve. Turn tool (B) until the ends of the tool make a flat piece (crease) in the wear sleeve. Do this in two or more places until the wear sleeve is loose.4. Remove tool (C) and the wear sleeve by hand.Install Crankshaft Rear Seal And Wear Sleeve
1. Install the crankshaft rear seal and wear sleeve with tooling (A) as follows: a) Put locator (1) in position on the crankshaft and install the three bolts that hold it in place.b) Put clean engine oil on the seal lip of seal (6) and on the outside diameter of wear sleeve (2).c) Install seal (6) on wear sleeve (2) from the end of the wear sleeve that has the bevel on the outside diameter. Make sure the lip of the seal is toward the inside of the engine and the bevel that is on the outside diameter of the wear sleeve is toward the outside of the engine when installed.d) Use 8M8060 Quick Cure Primer to clean the outside diameter of the crankshaft flange (3) and the inside diameter of wear sleeve (2).e) Put 9S3265 Retaining Compound on the outside diameter of crankshaft flange (3) and the inside diameter of wear sleeve (2). Make sure the lip of the seal is toward the inside of the engine and the outside diameter bevel of the wear sleeve is toward the outside of the engine.f) Put wear sleeve (2) with seal (6) on locator (1). Put installer (4) on locator (1) and install nut (5). Put lubrication on the face of the washer and the nut.g) Tighten nut (5) until installer (4) comes in contact with locator (1).h) Remove tooling (A) and check the wear sleeve and seal for correct installation.end by:a) install flywheel

Have questions with 09300-06291?





Group cross 09300-06291

Back to top