09300-06212 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

09300-06212 PUMP ASSY, INJECTI
Rating:
32
Buy PUMP ASSY, INJECTI 09300-06212 genuine, new aftermarket engine parts with delivery

Scheme ###:

000. [01] 09300-06212 PUMP ASSY, INJECTI 3310045600
003. [01] 19010-01610 BODY ASSY, INJECTI
003. [01] 19010-00962 BODY ASSY, INJECTI
004. [01] 09130-06901 GOVERNOR ASSY, MEC
005. [01] 09180-04100 TIMER ASSY, AUTOMA
006. [01] 09210-02840 PUMP ASSY, FUEL FE
007. [01] 09006-00570 COVER SUB-ASSY, TI
008. [01] 94914-03690 O-RING
009. [01] 90458-05750 KEY, WOODRUFF
010. [01] 09001-20360 NUT, TIMER ROUND
011. [01] 94901-81550 WASHER, COPPER PLA
012. [01] 09001-80410 COVER, CONTROL RAC
014. [04] 94901-15020 WASHER, STEEL PLAT
015. [04] 90258-10001 WASHER, SPRING
016. [04] 91266-10081 NUT, HEXAGON
017. [02] 94904-76880 BOLT, W/WASHER
018. [01] 94904-76910 BOLT, W/WASHER
019. [01] 94904-76900 BOLT, W/WASHER
020. [04] 94904-76890 BOLT, W/WASHER
021. [03] 09001-50090 WIRE, GOVERNOR HOU
022. [03] 09001-60040 SEAL, LEAD
023. [01] 09028-50110 CAP
024. [01] 94933-03581 TUBE, RUBBER
025. [01] 94935-03042 CLIP, CORD
026. [01] 19089-01160 OVER-HAUL KIT, GOV
026-001. [01] 09028-50021 CAP

Include in #3:

09300-06212 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09300-06212  3310045600  PUMP ASSY, INJECTI




Information:

3. Remove four bolts (3) and adjusting bolt (2). Remove the fan drive.Install Fan Drive
1. Put the fan drive in position on the engine and install the four bolts.2. Install the adjusting bolt. Install the fan and alternator belts. Make an adjustment to the tension. The correct belt tension is 7/8 in. (22 mm) movement for used belts and 3/4in. (19 mm) movement for new belts when measured with the application of a 25 lb. (11 kg) force half way between the two pulleys.3. Tighten the four fan drive bolts.4. Install the fan with the six bolts.Disassemble Fan Drive
start by: a) remove fan drive 1. Remove two bolts and washers (2). Remove hub (1). 2. Bend down the lock plate and remove bolts (4). Remove the lock plate and washer (3). 3. Use tool (A) to remove the pulley from the bracket assembly. 4. Remove the two bearings and the seal with tool (B).5. Remove the spacer.Assemble Fan Drive
1. Put multipurpose grease on the seal. Install the seal on the pulley with tool (A).2. Install the pulley in the bracket assembly. Fill half the space between the two bearings with multipurpose grease.3. Heat two bearings in oil. The temperature of the oil must be 300° 25°F (149° 14°C).
The bearing heating oil used to heat the bearings must have a flash point above 400°F (204°C).
4. Put multipurpose grease on the bearings. Install the bearing, spacer and bearing with tool (A). 5. Install the washer, lock plate and two bolts. Bend the lock plate up.6. Install the hub with the two bolts and lockwashers.end by: a) install fan drive

Have questions with 09300-06212?





Group cross 09300-06212

Back to top