09300-06031 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

09300-06031 PUMP ASSY, INJECTI
Rating:
77
Buy PUMP ASSY, INJECTI 09300-06031 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 09300-06031
002. GOVERNOR ASSY, MEC 09130-06340
003. COMPENSATOR SUB-AS 19260-01050
004. TIMER ASSY, AUTOMA 09180-03754
005. PUMP ASSY, FUEL FE 09210-02840
006. BODY ASSY, INJECTI 19010-00961

Scheme ###:

000. [01] 09300-06031 PUMP ASSY, INJECTI ME215039
003. [01] 19010-00962 BODY ASSY, INJECTI ME736900
004. [01] 09130-06340 GOVERNOR ASSY, MEC ME743354
005. [01] 09180-03754 TIMER ASSY, AUTOMA ME736904
006. [01] 09210-02840 PUMP ASSY, FUEL FE ME736506
007. [01] 09006-00480 COVER SUB-ASSY, TI ME736507
008. [01] 94914-03690 O-RING ME736557
009. [01] 90458-05750 KEY, WOODRUFF ME702920
010. [01] 09001-20360 NUT, TIMER ROUND ME736909
011. [01] 94901-81550 WASHER, COPPER PLA ME039681
012. [01] 09001-80410 COVER, CONTROL RAC ME736558
013. [01] 09028-50021 CAP ME035845
014. [04] 94901-15020 WASHER, STEEL PLAT MH005068
015. [04] 90258-10001 WASHER, SPRING MC327716
016. [04] 91266-10081 NUT, HEXAGON MF430122
017. [02] 94904-76880 BOLT, W/WASHER ME728977
018. [01] 94904-76910 BOLT, W/WASHER ME728980
019. [01] 94904-76900 BOLT, W/WASHER ME728979
020. [04] 94904-76890 BOLT, W/WASHER ME728978
023. [01] 09028-50050 CAP ME076458

Include in #3:

09300-06031 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09300-06031  ME215039  PUMP ASSY, INJECTI




Information:

(1) Depth of bore in block for liner ... .401 .001 in.(10.19 0.03 mm) For height of liner over top of block make reference to CYLINDER LINER PROJECTION.(2) Camshaft bearing bore (installed) ... 2.3150 .0020 in.(58.801 0.051 mm) Bore in block for camshaft bearings ... 2.5630 .0010 in.(65.100 0.025 mm)Depth to install camshaft bearings at both ends of block ... .06 .02 in.(1.5 0.5 mm) The camshaft bearing at the front of the block must be installed with oil holes in a horizontal position and joint at the top within 15° from vertical.(3) Bore in block for main bearings (standard size)(with main bearing caps torqued) ... 3.8160 .0005 in.(96.926 0.013 mm) Bore in block for main bearings .020 in. (0.51 mm oversize) ... 3.8360 .0005 in.(97.434 0.013 mm)(4) Dimension from center of main bearing bore to top of cylinder block (new) ... 15.5000 .0065 in.(393.700 0.165 mm)(5) Dimension from center of main bearing bore to bottom of cylinder block (new) ... 6.0625 .0040 in.(153.988 0.102 mm)(6) Torque for bolts holding bearing caps for main bearings: a. Put engine oil on threads and washer face.b. Tighten all bolts to ... 30 3 lb. ft.(40 4 N m)c. Put a mark on each bolt and cap.d. Tighten all bolts from mark ... 90° Install bearing caps with the part number toward the front of the engine. Be sure that the mark (number) on the bearing cap next to the bolt hole is in agreement with the mark in the cylinder block.(7) Clearance between slot in block and bearing cap (with main bearing caps torqued) ... .0017 in.(0.043 mm) loose to ... .0013 in.(0.033 mm) tight
There are holes in the bores for the main bearings, between the cylinders for piston cooler orifices. These holes must have orifices (8) installed.

Have questions with 09300-06031?





Group cross 09300-06031

Back to top