09300-05863 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

09300-05863 PUMP ASSY, INJECTI
Rating:
31
Buy PUMP ASSY, INJECTI 09300-05863 genuine, new aftermarket engine parts with delivery

Scheme ###:

000. [01] 09300-05863 PUMP ASSY, INJECTI ME217083
000. [01] 09300-05863 PUMP ASSY, INJECTI ME440798
006. [01] 19010-01320 BODY ASSY, INJECTI ME743238
007. [01] 19080-05841 GOVERNOR ASSY, MEC ME743239
008. [01] 94901-40210 WASHER, COUNTERSUN ME702043
009. [01] 94913-00210 KEY, WOODRUFF ME702047
010. [01] 09210-02750 PUMP ASSY, FUEL FE ME736121
010. [01] 09210-03320 PUMP ASSY, FUEL FE ME743435
011. [01] 09001-20220 NUT, TIMER ROUND ME702033
012. [01] 91518-08221 BOLT, W/WASHER MM500963
013. [06] 91418-06161 BOLT, W/WASHER ME702149
014. [01] 09001-80090 COVER, CONTROL RAC ME702251
015. [01] 09006-00451 COVER SUB-ASSY, TI ME736126
016. [04] 94901-15020 WASHER, STEEL PLAT MH005068
017. [04] 90258-10001 WASHER, SPRING MC327716
018. [04] 91266-10081 NUT, HEXAGON MF430122
019. [01] 94914-02840 O-RING MH035502
020. [01] 09181-12170 HUB, TIMER ME743402
020. [01] 09181-12180 HUB, TIMER ME743403
020. [01] 09180-03800 TIMER ASSY, AUTOMA ME743049
021. [01] 09185-10620 GEAR, TIMER DRIVIN ME736709
022. [04] 94904-07000 BOLT, HEXAGON ME736963

Include in #3:

09300-05863 as PUMP ASSY, INJECTI
09300-05863

Cross reference number



Part num Firm num Firm Name
09300-05863  ME217083  PUMP ASSY, INJECTI




Information:

2. Remove two short bolts (1) and two longer bolts (2) from manifold (3) and BrakeSaver housing.3. Remove the manifold from the control valve. 4. Remove the three bolts from elbows (5) and the control valve.5. Remove four bolts (4) that hold the control valve to the oil pan.6. Remove the control valve from under the oil pan.7. Make an inspection of the O-ring seals on the manifold and on the control valve. If there is wear or damage make a replacement of the O-ring seals.Install Brakesaver Control Valve
1. Put clean SAE 30 engine oil on O-ring seals (1).2. Put the control valve in position under the oil pan. Install the four bolts that hold the control valve to the oil pan.3. Install the elbow and the bolts that hold it to the side of the control valve. 4. Put SAE 30 engine oil on the O-ring seals of the manifold. Install manifold (2) in the control valve. Install the four bolts that hold the manifold to the BrakeSaver housing.5. Fill the engine with oil. See 3408 TRUCK ENGINE LUBRICATION AND MAINTENANCE GUIDE.Disassemble Brakesaver Control Valve
start by:a) remove BrakeSaver control valve 1. Remove O-ring seals (1) from the valve body.2. Remove four bolts (2) slowly and evenly from cover (4). Remove the cover.
Spring force is behind the cover at removal.
3. Remove cover (3) and the seal from the opposite end of the valve body. 4. Remove spool (8) as an assembly.5. Remove spring (7), stop (10), spring (6) and slug (9).6. Remove the seals and sleeve (5). 7. Remove bolt (11), plate (13) and diaphragm (12) from the spool. Make an inspection of the pin on the spool, and make a replacement of the pin if there is damage or wear.Assemble Brakesaver Control Valve
1. Install diaphragm (4) and plate (8) on valve spool (3). Make alignment of the hole in the plate valve with the pin on the spool. Install the bolt that holds the plate and the diaphragm in position.
When diaphragm (4) is installed on valve spool (3), make sure the fabric side is pulled down over the valve spool to make contact with it and the smooth (rubber coated) side is next to valve body.
2. Install sleeves (1) and the seals in the valve body. 3. Install the valve spool as an assembly into the valve body. As the valve spool is installed, make sure the edge of the diaphragm makes contact all the way around with the groove in the valve body. At this time the valve spool end must extend about 1.50 in. (38.1 mm) from the valve body. Push the valve spool about .25 in. (6.4 mm) - .50 in. (12.7 mm) farther into the valve body until a curved depression is caused between the valve spool and valve body. Make sure there are no wrinkles in the diaphragm. 4. Put cover (9) in position. Install the four bolts that hold the cover on the valve body. Move the valve spool in the

Have questions with 09300-05863?





Group cross 09300-05863

Back to top