09300-02260 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

Nozzle: 0935002470
09300-02260 PUMP ASSY, INJECTI
Rating:
3
Buy PUMP ASSY, INJECTI 09300-02260 genuine, new aftermarket engine parts with delivery

KIT List:

Body assy, injecti 1904400300
Timer assy, automa 0918030050
Pump assy, fuel fe 1922900060
Pump assy, fuel fe 1922900060
Governor assy, mec 1908900250

Components :

001. PUMP ASSY, INJECTI 09300-02260
002. BODY ASSY, INJECTI 09010-07400
003. TIMER ASSY, AUTOMA 09180-01710
004. PUMP ASSY, FUEL FE 09210-01140
005. PUMP ASSY, FUEL FE 09210-01551
006. GOVERNOR ASSY, MEC 19080-00093

Scheme ###:

000. [01] 09300-02260 PUMP ASSY, INJECTI ME016481
003. [01] 09010-07400 BODY ASSY, INJECTI ME016010
004. [01] 19080-00093 GOVERNOR ASSY, MEC ME703045
005. [01] 09210-01140 PUMP ASSY, FUEL FE ME016021
005. [01] 09210-01551 PUMP ASSY, FUEL FE ME703037
007. [01] 94913-00190 KEY, WOODRUFF ME703361
008. [01] 94901-50500 WASHER, SPRING ME008373
009. [01] 09001-20080 NUT, TIMER ROUND ME022426
009. [01] 09001-20260 NUT, TIMER ROUND ME703450
010. [01] 09001-80190 COVER, CONTROL RAC ME022416
013. [01] 90200-06511 WASHER, PLATE ME703364
014. [06] 94904-70620 BOLT, W/WASHER ME703359
015. [02] 09028-50021 CAP ME035845
016. [01] 09180-01710 TIMER ASSY, AUTOMA ME016163
017. [01] 09006-00180 COVER SUB-ASSY, TI ME016070
018. [01] 94914-03990 O-RING MH035501
019. [04] 94901-15020 WASHER, STEEL PLAT MH005068
020. [04] 90258-10001 WASHER, SPRING MC327716
021. [04] 91266-10081 NUT, HEXAGON MF430122
030. [01] 09647-20361 ACTUATOR SET, IDLE ME016169

Include in #3:

09300-02260 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09300-02260  ME016481  PUMP ASSY, INJECTI
ME016481    MITSUBISHI PUMP ASSY, INJECTI




Information:

Introduction
Diesel Particulate Filters (DPF) and Catalytic Converter Mufflers (CCM) are not applicable to all engines. Some engines contain a DPF and a CCM device that were installed as original equipment to meet engine emissions certification requirements. However, some engines may have had the devices installed during a retrofit program for emissions reduction.
Do not perform any procedure in this Special Instruction until you read this information and you understand this information.Procedure for Shipping the Diesel Particulate Filters (DPF)
Wear goggles, gloves, protective clothing, and a National Institute for Occupational Safety and Health (NIOSH) approved P95 or N95 half-face respirator when handling a used Diesel Particulate Filter or Catalytic Converter Muffler. Failure to do so could result in personal injury.
Place all the used Diesel Particulate Filter (DPF) center sections, regardless of condition, into a 0.152 mm (0.006 inch) thick plastic bag. Make sure that the bag is sealed before placing the DPF into a shipping container. This must be performed in order to contain any constituents from the used DPF during shipping. New replacement diesel particulate filters may come with a 0.152 mm (0.006 inch) plastic bag that can be used for wrapping the used DPF.Procedure for Shipping the Catalytic Converter Mufflers (CCM)
Seal the inlet port and the outlet port on all used Catalytic Converter Mufflers (CCM) with rubber caps or plastic caps. Various sized plastic caps can be ordered from the Cat Shop Supplies and Hand Tools catalog. Reference caps and plugs under the Shop Supplies section. An alternative is to seal the inlet ports and outlet ports with a 0.152 mm (0.006 inch) thick sheet of plastic and 50 mm (2 inch) wide sealing tape with good adhesive properties before shipping. Sealing or capping must be performed in order to contain any constituents from the used CCM during shipping.

Have questions with 09300-02260?





Group cross 09300-02260

Back to top