09300-01462 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

09300-01462 PUMP ASSY, INJECTI
Rating:
47
Buy PUMP ASSY, INJECTI 09300-01462 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 09300-01462
001. PUMP ASSY, INJECTI 09300-01462
001. PUMP ASSY, INJECTI 09300-01462
002. BODY ASSY, INJECTI 09010-06470
003. GOVERNOR ASSY, MEC 09130-01661
004. COVER ASSY, GOVERN 09145-00463
005. COMPENSATOR SUB-AS 19260-00120
006. COMPENSATOR SUB-AS 19260-00260
007. TIMER ASSY, AUTOMA 09180-02200
008. PUMP ASSY, FUEL FE 09210-00971

Scheme ###:

000. [01] 09300-01460 PUMP ASSY, INJECTI 22010-68160
000. [01] 09300-01461 PUMP ASSY, INJECTI 22010-68160
000. [01] 09300-01462 PUMP ASSY, INJECTI 22010-68160
001. [01] 09010-06470 BODY ASSY, INJECTI 22120-68160
001. [01] 09010-06471 BODY ASSY, INJECTI 22120-68160
002. [01] 09130-01664 GOVERNOR ASSY, MEC 22410-68160
002. [01] 09130-01663 GOVERNOR ASSY, MEC 22410-68160
002. [01] 09130-01661 GOVERNOR ASSY, MEC 22410-68160
003. [01] 09210-00971 PUMP ASSY, FUEL FE 22510-77130
004. [01] 09180-02200 TIMER ASSY, AUTOMA 22610-68030
007. [01] 09001-80061 COVER, CONTROL RAC 22116-46010
008. [01] 94913-00210 KEY, WOODRUFF 90099-13023
009. [01] 09001-20220 NUT, TIMER ROUND 22611-78030
010. [01] 91518-06201 BOLT, W/WASHER 90091-20620
011. [05] 94904-72690 BOLT, W/WASHER 90099-04319
014. [01] 09006-00250 COVER SUB-ASSY, TI 22812-68020
015. [04] 91266-10081 NUT, HEXAGON 94110-41000
016. [04] 94901-15020 WASHER, STEEL PLAT 90099-01463
017. [01] 94904-73910 BOLT, W/WASHER 90099-04346
019. [01] 94901-40210 WASHER, COUNTERSUN 90099-01500

Include in #3:

09300-01462 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09300-01462  22010-6816  PUMP ASSY, INJECTI




Information:

SUBJECT: A NEW INJECTION ACTUATION PRESSURE CONTROL VALVE CONNECTOR INCREASES ENGINE OPERATION
PROBLEM:
The injection actuation pressure (IAP) control valve connector may have been assembled incorrectly on some 3126B engine harnesses. This can lead to intermittent engine operation or can cause the engine to stop.
SOLUTION:
If your machine exhibits symptoms of intermittent engine operation or abruptly stopping, the IAP control valve connector should be disconnected from the machine, examined for solenoid contact problems and re-installed using a correct procedure.
Procedure for installing the IAP control valve connector
This procedure will describe how to properly install the 232-4367 Harness.
Required Parts
Qty Part Number Description
1 232-4367 Harness
Procure the part that is listed in the table.
Illustration 1. Left Side of a 3126B Engine on a D6N.
(1) IAP Control Valve
(2) IAP Control Valve Connector
Note: Illustration 1 is from a D6N that is equipped with a 3126B for photographical purposes. The location of the IAP Control Valve is the same for your machine.
Disconnect the IAP control valve connector (2) from the IAP Control Valve (1). See Illustration 1.
Cut the two wires directly behind the connector.
Using wire strippers, strip the ends of the two wires.
Install the 232-4367 Harness, by crimping the stripped wires inside the splice.
Note: Take care to connect the pink wire to the pink wire on one hand and the purple wire to the purple wire on the other hand.
Heat both heat shrinkable tubes in order to insulate both the splices.
Reconnect the repaired harness to the IAP Control Valve (1).
COPYRIGHT 2003 CATERPILLAR
ALL RIGHTS RESERVED

Have questions with 09300-01462?





Group cross 09300-01462

Back to top