Fuel injectors
  1. Home
  2. denso
  3. #09300-00361

09300-00361 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

09300-00361 PUMP ASSY, INJECTI
Rating:
12
Buy PUMP ASSY, INJECTI 09300-00361 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 09300-00361
002. BODY ASSY, INJECTI 09010-04330
003. GOVERNOR ASSY, COM 09070-00382
004. TIMER ASSY, AUTOMA 09180-01540
005. PUMP ASSY, FUEL FE 09210-00971

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09300-00361 PUMP ASSY, INJECTI 22010-68061
001. [01] 09010-04330 BODY ASSY, INJECTI 22120-68020
002. [01] 09070-00382 GOVERNOR ASSY, COM 22320-68040
003. [01] 09210-00971 PUMP ASSY, FUEL FE 22510-77130
004. [01] 09180-01540 TIMER ASSY, AUTOMA 22610-68011
007. [01] 09001-80061 COVER, CONTROL RAC 22116-46010
008. [01] 94913-00190 KEY, WOODRUFF 90099-13020
009. [01] 09001-20260 NUT, TIMER ROUND 22611-68010
010. [01] 91518-08221 BOLT, W/WASHER 90091-20804
011. [04] 94904-70620 BOLT, W/WASHER 90099-04526
014. [01] 09006-00100 COVER SUB-ASSY, TI 22812-68010
015. [04] 91260-10081 NUT, HEXAGON 94110-41000
016. [04] 94901-17570 WASHER, STEEL PLAT 90201-10018
018. [01] 09071-00011 BELLOWS ASSY, PNEU 22680-48061
019. [01] 94933-03581 TUBE, RUBBER 90099-33044
020. [01] 94905-61980 NUT 90099-05154
021. [01] 94935-03042 CLIP, CORD 90099-35023

Include in #3:

09300-00361 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09300-00361  22010-6806  PUMP ASSY, INJECTI




Information:

1. Disconnect hose (1) at governor control cylinder (2).2. Remove pin (4).3. Remove governor control cylinder (2).4. Note the position of linkage (3) in the lever, and remove linkage (3). The following steps are for installation of the governor control cylinder.5. Adjust linkage (3) so the distance between rod end centers is 84.07 mm (3.309 in).6. Install linkage (3) in its original position in the lever.7. Be sure lever (5) on the governor shaft is at 15 degrees from vertical (CW when viewed from the left side of the machine) with engine at low idle.8. Install control cylinder (2). Install pin (4) through link (3) and lever (5).9. Connect hose (1) to governor control cylinder (2).10. Adjust linkage (3) so lever (5) is at low idle when governor control cylinder is fully retracted.Disassemble & Assemble Governor Control Cylinder
Start By:a. remove governor control cylinder 1. Remove cover (1).
A spring force of 44.5 N (10 lb) will be released when the bolt that holds piston (8) is removed. Hold the components of the governor control cylinder to prevent unexpected movement of components and personal injury.
2. Remove the bolt that holds piston (6), and remove the piston and springs.3. Remove O-ring seal (2) and sleeve (5).4. Remove seals (3) and (4) from piston (6). The following steps are for the assembly of the governor control cylinder.5. Install lip-type seal (3) and "T" seal on the piston (6). Install the lip-type seal with the lip facing the cylinder pressure source.6. Install shell (5) in the air chamber body.7. Put 5P-0960 Multipurpose Grease inside the shell.8. Carefully install piston (6) and springs into the air chamber body.9. Install the bolt to hold the piston.10. Install O-ring seal (2) and cover (1).End By:a. install governor control cylinder

Have questions with 09300-00361?





09300-00350 PUMP ASSY, INJECTI 09300-00340 09300-00330 09300-00320 09300-00310
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09300-00361

Back to top