Fuel injectors
  1. Home
  2. denso
  3. #09300-00081

09300-00081 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

09300-00081 PUMP ASSY, INJECTI
Rating:
45
Buy PUMP ASSY, INJECTI 09300-00081 genuine, new aftermarket engine parts with delivery

Components :

001. PUMP ASSY, INJECTI 09300-00081
002. SWITCH KIT, CONTRO 09009-90241
003. BODY ASSY, INJECTI 09010-03691
004. GOVERNOR ASSY, MEC 09080-05284
005. TIMER ASSY, AUTOMA 09180-01131
006. PUMP ASSY, FUEL FE 09210-00561
007. PUMP ASSY, FUEL FE 09210-01140
008. PUMP ASSY, FUEL FE 09210-01551

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09300-00081 PUMP ASSY, INJECTI ME016005
005. [01] 09010-03691 BODY ASSY, INJECTI ME016010
006. [01] 09080-05284 GOVERNOR ASSY, MEC ME016018
007. [06] 94904-70620 BOLT, W/WASHER ME703359
008. [01] 94913-00190 KEY, WOODRUFF ME703361
009. [01] 94901-50500 WASHER, SPRING ME008373
010. [01] 09001-20260 NUT, TIMER ROUND ME703450
012. [01] 09210-01551 PUMP ASSY, FUEL FE ME703037
012. [01] 09210-01140 PUMP ASSY, FUEL FE ME016021
012. [01] 09210-00561 PUMP ASSY, FUEL FE ME029078
014. [01] 09001-80190 COVER, CONTROL RAC ME022416
015. [01] 90200-06511 WASHER, PLATE ME703364
016. [01] 09009-90241 SWITCH KIT, CONTRO ME016025
017. [01] 09180-01131 TIMER ASSY, AUTOMA ME012704
018. [01] 09006-00130 COVER SUB-ASSY, TI ME016038
019. [01] 94914-03990 O-RING MH035501
020. [04] 94901-15020 WASHER, STEEL PLAT MH005068
021. [04] 90258-10001 WASHER, SPRING MC327716
022. [04] 91266-10081 NUT, HEXAGON MF430122

Include in #3:

09300-00081 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09300-00081  ME016005  PUMP ASSY, INJECTI




Information:

1. Disconnect hose (1) at governor control cylinder (2).2. Remove pin (4).3. Remove governor control cylinder (2).4. Note the position of linkage (3) in the lever, and remove linkage (3). The following steps are for installation of the governor control cylinder.5. Adjust linkage (3) so the distance between rod end centers is 84.07 mm (3.309 in).6. Install linkage (3) in its original position in the lever.7. Be sure lever (5) on the governor shaft is at 15 degrees from vertical (CW when viewed from the left side of the machine) with engine at low idle.8. Install control cylinder (2). Install pin (4) through link (3) and lever (5).9. Connect hose (1) to governor control cylinder (2).10. Adjust linkage (3) so lever (5) is at low idle when governor control cylinder is fully retracted.Disassemble & Assemble Governor Control Cylinder
Start By:a. remove governor control cylinder 1. Remove cover (1).
A spring force of 44.5 N (10 lb) will be released when the bolt that holds piston (8) is removed. Hold the components of the governor control cylinder to prevent unexpected movement of components and personal injury.
2. Remove the bolt that holds piston (6), and remove the piston and springs.3. Remove O-ring seal (2) and sleeve (5).4. Remove seals (3) and (4) from piston (6). The following steps are for the assembly of the governor control cylinder.5. Install lip-type seal (3) and "T" seal on the piston (6). Install the lip-type seal with the lip facing the cylinder pressure source.6. Install shell (5) in the air chamber body.7. Put 5P-0960 Multipurpose Grease inside the shell.8. Carefully install piston (6) and springs into the air chamber body.9. Install the bolt to hold the piston.10. Install O-ring seal (2) and cover (1).End By:a. install governor control cylinder

Have questions with 09300-00081?





09300-00071 PUMP ASSY, INJECTI 09300-00060 09300-00050 09300-00040 09300-00030
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09300-00081

Back to top