09210-01401 PUMP ASSY, FUEL FE Denso Cross


 

Information pump assy, fuel fe

09210-01401 PUMP ASSY, FUEL FE
Rating:
65
Buy PUMP ASSY, FUEL FE 09210-01401 genuine, new aftermarket engine parts with delivery

Scheme ###:

000. [01] 09210-01401 PUMP ASSY, FUEL FE 09210-01400
002. [01] 09212-00161 HOUSING SUB-ASSY, 09212-00161
002-001. [01] 09216-80150 ROD, FEED PUMP PUS 09216-80150
002-001. [1C] 09216-80070 ROD, FEED PUMP PUS 09216-80070
002-001. [1C] 09216-80060 ROD, FEED PUMP PUS 09216-80060
002-001. [1C] 09216-80050 ROD, FEED PUMP PUS 09216-80050
002-001. [1C] 09216-80040 ROD, FEED PUMP PUS 09216-80040
002-001. [1C] 09216-80030 ROD, FEED PUMP PUS 09216-80030
002-001. [1C] 09216-80010 ROD, FEED PUMP PUS 09216-80010
002-001. [01] 09216-80150 ROD, FEED PUMP PUS 09216-80150
002-002. [01] 94915-02700 SEAL, OIL
002-002. [01] 94915-00970 SEAL, OIL 94915-00970
003. [02] 09212-10011 VALVE, FEED PUMP C 09212-10010
004. [02] 09212-40010 SPRING, FEED PUMP 09212-40010
005. [02] 09212-50010 GASKET, CHECK VALV 09212-50010
006. [01] 09212-70010 SUPPORT, VALVE 09212-70010
007. [01] 09213-00220 PUMP SUB-ASSY, PRI
008. [01] 09217-10011 PISTON, FEED PUMP 09217-10010
009. [01] 09217-40030 TAPPET, FEED PUMP 09217-40030
010. [01] 09217-60010 ROLLER, FEED PUMP 09217-60010
011. [01] 09217-80010 PIN, FEED PUMP TAP 09217-80010
012. [02] 09217-90050 BLOCK, FEED PUMP T 09217-90050
013. [01] 09218-20040 SPRING, FEED PUMP 09218-20040
014. [01] 09218-40021 PLUG, FEED PUMP PI 09218-40020
015. [01] 09222-00040 FILTER, FEED PUMP 09222-00040
016. [01] 09222-30070 SCREW, FUEL PIPE H 09222-30070
017. [04] 09022-20070 WASHER, FUEL PIPE 09022-20070
018. [01] 94901-81240 WASHER, COPPER PLA 94901-81240
020. [01] 94907-20940 RING, SNAP 94907-20940
022. [01] 94918-00310 SCREW, HOLLOW 94918-00310
024. [01] 94918-10300 NIPPLE, SWIVELING 94918-10300
025. [01] 94918-10160 NIPPLE, SWIVELING 94918-10160

Include in #3:

09210-01401 as PUMP ASSY, FUEL FE

Cross reference number



Part num Firm num Firm Name
09210-01401  09210-0140  PUMP ASSY, FUEL FE




Information:


The clutch warning sign is located on the clutch housing (if equipped).
Clutch warning sign.
Rotating gears- finger or hand entanglement. Do not service until reading the operator's manual.
Located near batteries (if equipped):
Improper jumper cable connections can cause an explosion resulting in personal injury.Batteries may be located in separate compartments. When using jumper cables, always connect positive (+) cable to positive (+) terminal of battery connected to starter solenoid and negative (-) cable from external source to starter negative (-) terminal (if machine not equipped with starter negative terminal, connect to engine block.) Follow procedure in the operation manual.
Located on the mounting base (if equipped) near the lifting holes:
Improper lift rigging can allow load to tumble causing injury and damage.
Located on the fuel tank (if equipped):
Drain fuel tank before lifting unit. Lifting this unit when fuel is present in the tank could result in separation of the tank from the base and cause personal injury or death.
Located on engine lifting eye cover assembly.
Do not use the engine lifting eyes to remove the engine and generator together.
Located on the side panels of the generator (if equipped):
Do not connect generator to a utility electrical distribution system unless it is isolated from the system. Electrical feedback into the distribution system can occur and could cause personal injury or death.Open and secure main distribution system switch. Or if the connection is permanent, install a double throw transfer switch to prevent electrical feedback. Some generators are specifically approved by a utility to run in parallel with the distribution system and isolation may not be required. Always check with your utility as to the applicable circumstances.
Located on the outside of the control panel vandal door (if equipped):
Always operate this unit with the vandal door open. Operating the unit with the vandal door closed restricts access to the emergency stop button and could result in injury or death.
Located on the outside of the control panel vandal door (if equipped), above the emergency stop warning:
Do not operator or work on this engine or generator set unless you have read and understand the instructions and warnings in the operation and maintenance manuals. Failure to follow the warnings and instructions could result in injury or death. Contact any Caterpillar dealer for replacement manuals. Proper care is your responsibility.
Located inside the generator housing (if equipped):
Before working inside the generator, make sure that the starting motor can not be activated by any automatic or manual signal. When servicing or repairing electric power generation equipment make sure the unit is off-line (disconnected from utility and/or other generators power service), and either locked out or tagged DO NOT OPERATE. Remove all fuses. Make sure the generator engine is stopped. Make sure all batteries are disconnected. Make sure all capacitors are discharged. Failure to do so could result in personal injury or death. Make sure residual voltage in the rotor, stator and the generator is discharged.
General Hazard Information
Attach a DO NOT OPERATE or similar warning tag to the start switch or controls before performing maintenance

Have questions with 09210-01401?





Group cross 09210-01401

Back to top