Information pump assy, fuel fe
Rating:
KIT List:
| Pump assy, fuel fe | 1922900060 |
| Pump assy, fuel fe | 1922900060 |
| Pump assy, fuel fe | 1922900060 |
Scheme ###:
| 000. | [01] | 09210-01200 | PUMP ASSY, FUEL FE | 5-15750027-0 |
| 003. | [01] | 09212-00340 | HOUSING SUB-ASSY, | |
| 003-001. | [01] | 09216-80150 | ROD, FEED PUMP PUS | |
| 003-002. | [01] | 94915-02700 | SEAL, OIL | |
| 004. | [02] | 09212-10011 | VALVE, FEED PUMP C | 5-15755001-0 |
| 005. | [02] | 09212-40010 | SPRING, FEED PUMP | 5-15755002-0 |
| 006. | [02] | 09212-50010 | GASKET, CHECK VALV | 5-15759001-0 |
| 007. | [01] | 09212-70010 | SUPPORT, VALVE | |
| 008. | [01] | 09213-00130 | PUMP SUB-ASSY, PRI | 5-15761003-0 |
| 008. | [01] | 09213-00220 | PUMP SUB-ASSY, PRI | |
| 009. | [01] | 09217-10011 | PISTON, FEED PUMP | |
| 011. | [01] | 09217-40030 | TAPPET, FEED PUMP | |
| 012. | [01] | 09217-60010 | ROLLER, FEED PUMP | |
| 013. | [01] | 09217-80010 | PIN, FEED PUMP TAP | |
| 014. | [02] | 09217-90050 | BLOCK, FEED PUMP T | |
| 015. | [01] | 94907-20940 | RING, SNAP | |
| 016. | [01] | 09218-20020 | SPRING, FEED PUMP | |
| 017. | [01] | 94901-81240 | WASHER, COPPER PLA | |
| 018. | [01] | 09218-40021 | PLUG, FEED PUMP PI | |
| 019. | [01] | 09222-00040 | FILTER, FEED PUMP | |
| 020. | [01] | 09222-30070 | SCREW, FUEL PIPE H | 5-15759002-0 |
| 021. | [01] | 94918-00310 | SCREW, HOLLOW | 5-15759003-0 |
| 022. | [04] | 09022-20070 | WASHER, FUEL PIPE | 5-15759004-0 |
Include in #3:
Cross reference number
| Part num | Firm num | Firm | Name |
| 09210-01200 | 5-15750027 | PUMP ASSY, FUEL FE | |
| 5-15750027-0 | ISUZU | PUMP ASSY, FUEL FE |
Information:
(8) Piston cooling orifice.
There are holes in the bores for the main bearings, between the cylinders for piston cooling orifices. These holes must have orifices (8) installed.
(9) Distance two dowels extend from the surface of the cylinder block ... 19.8 0.5 mm (.78 .02 in)(10) Distance hollow dowel extends from the surface of the cylinder block ... 16.0 0.5 mm (.63 .02 in)(11) Depth to install two dowels below the surface of the cylinder block (apply loctite #11358) ... 1.0 0.5 mm (.04 .02 in)(12) Distance dowels extend from the front face of the cylinder block ... 22.4 0.5 mm (.88 .02 in)(13) Distance stud extends from the front face of the cylinder block ... 15.7 0.5 mm (.62 .02 in)(14) Distance two dowels extend from the rear face of the cylinder block ... 12.7 0.5 mm (.50 .02 in)
There are holes in the bores for the main bearings, between the cylinders for piston cooling orifices. These holes must have orifices (8) installed.
(9) Distance two dowels extend from the surface of the cylinder block ... 19.8 0.5 mm (.78 .02 in)(10) Distance hollow dowel extends from the surface of the cylinder block ... 16.0 0.5 mm (.63 .02 in)(11) Depth to install two dowels below the surface of the cylinder block (apply loctite #11358) ... 1.0 0.5 mm (.04 .02 in)(12) Distance dowels extend from the front face of the cylinder block ... 22.4 0.5 mm (.88 .02 in)(13) Distance stud extends from the front face of the cylinder block ... 15.7 0.5 mm (.62 .02 in)(14) Distance two dowels extend from the rear face of the cylinder block ... 12.7 0.5 mm (.50 .02 in)