Fuel injectors
  1. Home
  2. denso
  3. #09200-05430

09200-05430 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

Nozzle: 0935005480
09200-05430 PUMP ASSY, INJECTI
Rating:
61
Buy PUMP ASSY, INJECTI 09200-05430 genuine, new aftermarket engine parts with delivery

KIT List:

Pump assy, fuel fe 1922900060
Body assy, injecti 1904400300
Governor assy, mec 1908900170

Components :

001. PUMP ASSY, INJECTI 09200-05430
002. PUMP ASSY, FUEL FE 09210-01551
003. BODY ASSY, INJECTI 19010-01060
004. GOVERNOR ASSY, MEC 19080-07020
005. OVER-HAUL KIT, GOV 19089-01260

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09200-05430 PUMP ASSY, INJECTI 32C6502320
005. [01] 19010-01060 BODY ASSY, INJECTI
006. [01] 19080-07020 GOVERNOR ASSY, MEC
007. [01] 09001-80241 COVER, CONTROL RAC 09001-80241
008. [01] 94905-02450 NUT, HEXAGON 94905-02450
009. [01] 94913-00190 KEY, WOODRUFF 94913-00190
010. [01] 94901-50500 WASHER, SPRING 94901-50500
012. [01] 09210-01551 PUMP ASSY, FUEL FE 34461-09050
013. [01] 91518-08221 BOLT, W/WASHER 91518-08221
014. [06] 91418-06161 BOLT, W/WASHER 91418-06161
015. [01] 19089-01260 OVER-HAUL KIT, GOV 32B6519510
015-001. [02] 09103-10310 NUT, CAP
015-002. [01] 09103-10320 NUT, CAP
015-003. [01] 09103-10360 NUT, CAP
015-004. [02] 94914-04060 O-RING
015-005. [02] 94907-21500 RING, SNAP
015-006. [01] 94901-81020 WASHER, COPPER PLA 94901-81020

Include in #3:

09200-05430 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09200-05430  32C6502320  PUMP ASSY, INJECTI
32C6502320    MITSUBISHI PUMP ASSY, INJECTI




Information:

1. Remove the fuel injection nozzle assembly, and put the piston on TDC (top dead center) for the respective cylinder for which the valve stem seal and O-ring seals are to be removed.2. Install air chuck adapter (2). Fasten a pressure air source to pressurize the cylinder.3. Use tooling (A) to compress the valve springs. Use magnet bar (1) to hold the keepers.4. Remove tool (A), and remove the valve springs and retainer. 5. Remove exhaust valve O-ring seal (3) and inlet valve guide seal (4).
Do not release air pressure in the cylinder until the valve springs and retainer have been installed. Failure to do so will let the valve fall into the top of the piston. If the piston is not at TDC (top dead center) the valve can fall into the cylinder making cylinder head removal necessary.
Install Valve Guide Seals
1. Install spring seating washer (1). 2. Put clean engine oil on the part of valve guide seal (2) that makes contact with the valve stem. Install valve guide seal (2).
The closed coil of the spring must be toward the cylinder rod.
3. Put inner and outer springs (4) and retainer (3) in position.
The locks can be thrown from the valve when the compressor is released if they are not in their correct position on the valve stem.
4. Use tool (A) to compress the valve springs so the keepers can be installed.5. Use tool (B) to install the keepers.6. Repeat Steps 1-4 for O-ring seals (5) on the exhaust valve.7. Move the piston off T.D.C. (top dead center) and tap the valve spring retainer with a soft hammer to be sure the retainers are properly seated.8. Install the fuel injection nozzle assembly.End By:a. install rocker shaft and push rods

Have questions with 09200-05430?





09210-05010 PUMP ASSY, FUEL FE 09210-05000 09210-03440 09210-03420 09210-03390
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09200-05430

Back to top