Fuel injectors
  1. Home
  2. denso
  3. #09200-03890

09200-03890 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

Nozzle: 0935005480
09200-03890 PUMP ASSY, INJECTI
Rating:
21
Buy PUMP ASSY, INJECTI 09200-03890 genuine, new aftermarket engine parts with delivery

KIT List:

Pump assy, fuel fe 1922900060
Body assy, injecti 1904400300
Governor assy, mec 1908900170

Components :

001. PUMP ASSY, INJECTI 09200-03890
002. PUMP ASSY, FUEL FE 09210-01291
003. BODY ASSY, INJECTI 19010-00480
004. GOVERNOR ASSY, MEC 19080-06150
005. OVER-HAUL KIT, GOV 19089-01090
006. OVER-HAUL KIT, GOV 19089-01260

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09200-03890 PUMP ASSY, INJECTI 32C6502160
005. [01] 19010-00480 BODY ASSY, INJECTI
006. [01] 19080-06150 GOVERNOR ASSY, MEC
007. [01] 09001-80220 COVER, CONTROL RAC
008. [01] 94905-02450 NUT, HEXAGON 94905-02450
009. [01] 94913-00190 KEY, WOODRUFF 94913-00190
010. [01] 94901-50500 WASHER, SPRING 94901-50500
012. [01] 09210-01291 PUMP ASSY, FUEL FE 34461-09060
013. [01] 91518-08221 BOLT, W/WASHER 91518-08221
014. [06] 91418-06161 BOLT, W/WASHER 91418-06161
015. [01] 19089-01260 OVER-HAUL KIT, GOV 32B6519510
015. [01] 19089-01090 OVER-HAUL KIT, GOV 32B6509510
015-001. [02] 09103-10260 NUT, CAP
015-001. [02] 09103-10310 NUT, CAP
015-002. [01] 09103-10270 NUT, CAP
015-002. [01] 09103-10320 NUT, CAP
015-003. [01] 09103-10360 NUT, CAP
015-003. [01] 09103-10280 NUT, CAP
015-004. [02] 94914-02141 O-RING
015-004. [02] 94914-04060 O-RING
015-005. [02] 94907-21500 RING, SNAP
015-006. [01] 94901-81020 WASHER, COPPER PLA 94901-81020

Include in #3:

09200-03890 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09200-03890  32C6502160  PUMP ASSY, INJECTI
32C6502160    MITSUBISHI PUMP ASSY, INJECTI




Information:

Start By:a. remove oil pumpb. remove oil pan plate 1. Turn the crankshaft until two pistons are at the bottom center. Remove connecting rod caps (1) from the two connecting rods. Remove the lower half of the rod bearing from the rod bearing cap.2. Push the connecting rods away from the crankshaft. Remove the upper half of the rod bearing from the connecting rod. Install the connecting rod bearings dry when the clearance checks are made. Put clean engine oil on the connecting rod bearings for final assembly.3. Install the upper half of the rod bearing in the connecting rod.4. Install the lower half of the rod bearing in the connecting rod cap. Be sure the tabs in the back of the connecting rod bearings are in the tab grooves of the connecting rod and cap. 5. Use Plastigage (A) to check the connecting rod bearing clearance.6. Put Plastigage (A) on the connecting rod bearing.7. Put 2P2506 Thread Lubricant on the threads of the rod bolts and seat surfaces of the nuts.
When connecting rod caps are installed, make sure the number on the side of the cap is next to and respective with the number on the side of the connecting rod.
Do not turn the crankshaft when Plastigage (A) is in position.
Do not use an impact wrench to tighten the nuts the additional 90°.
8. Install connecting rod cap (1). Install the nuts. Tighten the nuts to a torque of 40 4 N m (30 3 lb ft). Put a mark on each nut and the end of each bolt. Tighten the nuts 90° more. Remove the connecting rod caps. Remove Plastigage (A) and measure the width of the Plastigage. The connecting rod clearance must be 0.076 to 0.168 mm (.0030 to .0066 in) for new bearings. The maximum clearance with used bearings is 0.25 mm (.010 in).9. Install the connecting rod caps and tighten the nuts as in Step 8.10. Do Steps 1 through 9 for the remainder of the connecting rod bearings.End By:a. install oil pan plateb. install oil pump

Have questions with 09200-03890?





09210-05010 PUMP ASSY, FUEL FE 09210-05000 09210-03390 09210-03310 09210-03300
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09200-03890

Back to top