Fuel injectors
  1. Home
  2. denso
  3. #09200-03813

09200-03813 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

09200-03813 PUMP ASSY, INJECTI
Rating:
62
Buy PUMP ASSY, INJECTI 09200-03813 genuine, new aftermarket engine parts with delivery

Scheme ###:

PUMP ASSY, INJECTI
000. [01] 09200-03813 PUMP ASSY, INJECTI 22010-8462
000. [01] 09200-03813 PUMP ASSY, INJECTI S2201-08462-B
003. [01] 19010-01540 BODY ASSY, INJECTI
004. [01] 09130-06551 GOVERNOR ASSY, MEC
005. [01] 09180-04001 TIMER ASSY, AUTOMA S2251-02870-A
006. [01] 09001-20340 NUT, TIMER ROUND S2282-52240-A
007. [01] 09250-01061 COUPLING ASSY S2261-01860-A
008. [01] 90458-05750 KEY, WOODRUFF S2289-11070-A
009. [01] 09210-03271 PUMP ASSY, FUEL FE S2257-01860-A
010. [01] 09001-80381 COVER, CONTROL RAC S2211-41200-A
011. [01] 94901-81550 WASHER, COPPER PLA SL722-02215
012. [01] 94904-76900 BOLT, W/WASHER S2281-53230-A
013. [04] 94904-76890 BOLT, W/WASHER S2281-53210-A
014. [01] 94904-76910 BOLT, W/WASHER S2281-53240-A
015. [02] 94904-76880 BOLT, W/WASHER S2281-53320-A
019. [01] 09028-50030 CAP S2232-31210-A
020. [01] 09028-50050 CAP S2232-31430-A
021. [01] 09031-00450 VALVE ASSY, OVERFL S2210-71570-A
022. [02] 94901-02480 WASHER S2284-71940-A
023. [01] 09045-30160 STAY, INJECTION PU S1140-91261-A
024. [02] 91418-08351 BOLT, W/WASHER S2281-53380-A
025. [01] 09069-00870 BRACKET SUB-ASSY, 22044-1400A
026. [02] 91808-08121 BOLT, FLANGE S2281-53330-A
027. [01] 09028-50030 CAP S2232-31210-A

Include in #3:

09200-03813 as PUMP ASSY, INJECTI
09200-03813

Cross reference number



Part num Firm num Firm Name
09200-03813  22010-8462  PUMP ASSY, INJECTI




Information:

Start By:a. remove fuel injection lines 1. Remove bolt (1) and clamp (2) from the fuel injection nozzles to be removed.2. Install Tool (A) with the inside lip of the puller on the lower stepped diameter of the nozzle and the tip of the button in the threaded hole for bolt (1).
Do not exceed a torque of 17 N m (150 lb in) on the screw of Tool (A) during removal of the nozzle. Added force can cause the stem of the nozzle to bend or break off.
3. Tighten the screw of Tool (A) to a maximum torque of 17 N m (150 lb in) to remove fuel injection nozzle (3).4. If the fuel injection nozzle can not be removed with a maximum torque of 17 N m (150 lb in) on the screw of Tool (A), remove Tool (A).
Typical Example5. Remove the protective cap from fuel injection nozzle (3), and install Tool (B) as shown.
Hold Tool (B) so the center line of the tool is in alignment with the centerline of fuel injection nozzle (3). This will prevent distortion of the nozzle which can cause it to bend or break off during removal.
6. Remove the fuel injection nozzle with Tool (B).7. If Tool (B) was used to remove the fuel injection nozzle, replace the nozzle.8. If Tool (A) was used to remove the fuel injection nozzle, remove the carbon dam seal on the end of the nozzle.Install Fuel Injection Nozzle
1. Use Tool (C) to clean the bore for the fuel injection nozzle. Use an open end wrench or tap driver to turn Tool (C).2. Make reference to Special Instruction, Form No. SEHS7292, for the use of Tool (D). Clean the fuel injection nozzle with Tool (D). 3. Install a new seal (4) on fuel injection nozzle (3).4. Put carbon dam seal (5) on the small end of Tool (E). Expand the carbon dam seal by sliding it to the large end. Put Tool (E) against the fuel injection nozzle. Slide carbon dam seal (5) off Tool (E) on to the nozzle. Slide the carbon dam seal into position in the groove on the nozzle as shown. 5. Put fuel injection nozzle (3) in position in the cylinder head. Install clamp (2) and bolt (1) to hold the nozzle in position.End By:a. install fuel injection lines

Have questions with 09200-03813?





09210-05010 PUMP ASSY, FUEL FE 09210-05000 09210-03390 09210-03271 09210-03240
01700061 PUMP ASSY, FUEL FE 01705213 PUMP ASSY, INJECTI 01705223 01705242 01705252

Group cross 09200-03813

Back to top