Information pump assy, injecti
Rating:
Compare Prices: .
As an associate, we earn commssions on qualifying purchases through the links below
RDLIFT-PART Fuel Injection Pump 092000-3690 32B65-03080 Compatible for Mitsubishi Forklift Engine S6S
RDLIFT-PART 🟢🔅Part Number:092000-3690 32B65-03080 || 🟢🔅Application：For Mitsubishi Forklift Engine S6S || 🟢🔅Order Include:1xFuel Injection Pump || 🟢🔅Condition: New || 🟢🔅Warrantly :6 Months || 🟢🔅note：Our products offer extremely high cost performance. You only need to pay half the price of the original factory parts, yet you can enjoy the same performance as the original parts. All of our products are of excellent quality.
RDLIFT-PART 🟢🔅Part Number:092000-3690 32B65-03080 || 🟢🔅Application：For Mitsubishi Forklift Engine S6S || 🟢🔅Order Include:1xFuel Injection Pump || 🟢🔅Condition: New || 🟢🔅Warrantly :6 Months || 🟢🔅note：Our products offer extremely high cost performance. You only need to pay half the price of the original factory parts, yet you can enjoy the same performance as the original parts. All of our products are of excellent quality.
Scheme ###:
| 000. | [01] | 09200-03690 | PUMP ASSY, INJECTI | 32B6503080 |
| 000. | [01] | 09200-03691 | PUMP ASSY, INJECTI | 32B6513080 |
| 000. | [01] | 09200-03692 | PUMP ASSY, INJECTI | 32B6523080 |
| 005. | [01] | 19010-00761 | BODY ASSY, INJECTI | |
| 006. | [01] | 19080-06060 | GOVERNOR ASSY, MEC | |
| 007. | [01] | 09001-80241 | COVER, CONTROL RAC | 09001-80241 |
| 008. | [01] | 94905-02450 | NUT, HEXAGON | 94905-02450 |
| 009. | [01] | 94913-00190 | KEY, WOODRUFF | 94913-00190 |
| 010. | [01] | 94901-50500 | WASHER, SPRING | 94901-50500 |
| 012. | [01] | 09210-01551 | PUMP ASSY, FUEL FE | 34461-09050 |
| 013. | [01] | 91518-08221 | BOLT, W/WASHER | 91518-08221 |
| 014. | [06] | 91418-06161 | BOLT, W/WASHER | 91418-06161 |
| 015. | [01] | 19089-01260 | OVER-HAUL KIT, GOV | 32B6519510 |
| 015. | [01] | 19089-01090 | OVER-HAUL KIT, GOV | 32B6509510 |
| 015-001. | [02] | 09103-10260 | NUT, CAP | |
| 015-001. | [02] | 09103-10310 | NUT, CAP | |
| 015-002. | [01] | 09103-10270 | NUT, CAP | |
| 015-002. | [01] | 09103-10320 | NUT, CAP | |
| 015-003. | [01] | 09103-10360 | NUT, CAP | |
| 015-003. | [01] | 09103-10280 | NUT, CAP | |
| 015-004. | [02] | 94914-02141 | O-RING | |
| 015-004. | [02] | 94914-04060 | O-RING | |
| 015-005. | [02] | 94907-21500 | RING, SNAP | |
| 015-006. | [01] | 94901-81020 | WASHER, COPPER PLA | 94901-81020 |
Include in #3:
09200-03691
as PUMP ASSY, INJECTI
Cross reference number
| Part num | Firm num | Firm | Name |
| 09200-03691 | 32B6513080 | PUMP ASSY, INJECTI |
Information:
1. Attach lifting strap to engine compartment cover. Remove two cotter pins and washers (1), remove four bolts (2). Lift off cover. 2. Loosen hose clamps (3) and (4) and remove hose (5). Remove three bolts (6) and remove ether aid cover (7). 3. Disconnect ether aid line (8), electrical connector (9), and loosen eight 1/4 turn fasteners (10). Remove heat shields (11) and (12). 4. Mark and disconnect starter wires (13) and ground strap (14). 5. Mark and disconnect alternator wires (15) and (16), temperature sending unit wire (17), cable mounting bracket (18), and electrical connector (19). Disconnect and remove flexible exhaust pipe (20). Disconnect two heater hoses (21). 6. Disconnect throttle linkage (22), remove two bolts (23). Set throttle linkage mounting bracket aside. Shut off and disconnect two fuel lines (24). 7. Disconnect throttle cable clip (25). Disconnect electrical wire (26), electrical connector (27) and governor wiring (28). 8. Install tool (A), lifting strap and tool (B) as shown, to support hydraulic pump. Remove twelve hydraulic pump mounting bolts (29). 9. Install lifting chains and remove four bolts and bushings (30).10. Remove engine. The following steps are to install the engine.11. Position engine in vehicle and install four bolts and bushings (30).12. Connect hydraulic pump to engine with twelve mounting bolts (29).13. Remove tooling (A) and (B), and the lifting strap that was supporting the hydraulic pump.14. Connect governor wiring (28), electrical connector (27), and wire (26). Connect throttle cable clip (25).15. Connect two fuel lines (24). Position throttle linkage mounting bracket and secure with two bolts (23). Connect throttle linkage (22).16. Connect two heater hoses (21) and flexible exhaust pipe (20). Connect alternator wires (15) and (16), temperature sending unit wire (17), cable mounting bracket (18) and electrical connector (19).17. Connect starter wires (13) and ground strap (14).18. Replace heat shields (11) and (12), fasten with eight 1/4 turn fasteners. Connect electrical connector (9) and ether aid line (8).19. Replace ether aid cover (7) and secure with three bolts (6). Replace hose (5) and connect with clamps (3) and (4).20. Attach engine compartment cover with four bolts (2) and connect cylinders with cotter pins and washers (1).End By:a. install radiator