09200-03680 PUMP ASSY, INJECTI Denso Cross


 

Information pump assy, injecti

09200-03680 PUMP ASSY, INJECTI
Rating:
71
Buy PUMP ASSY, INJECTI 09200-03680 genuine, new aftermarket engine parts with delivery

KIT List:

Pump assy, fuel fe 1922900060
Body assy, injecti 1904400360
Governor assy, mec 1908900170

Components :

001. PUMP ASSY, INJECTI 09200-03680
002. PUMP ASSY, FUEL FE 09210-03130
003. BODY ASSY, INJECTI 19010-01480
004. GOVERNOR ASSY, MEC 19080-05900

Scheme ###:

000. [01] 09200-03680 PUMP ASSY, INJECTI RE501033
001. [01] 19010-01480 BODY ASSY, INJECTI
002. [01] 19080-05900 GOVERNOR ASSY, MEC
003. [01] 09210-03130 PUMP ASSY, FUEL FE
004. [01] 09255-10790 BLOCK, COUPLING
005. [01] 94901-50900 WASHER, SPRING
006. [01] 94905-03570 NUT, HEXAGON
011. [01] 09001-80140 COVER, CONTROL RAC
012. [06] 91418-06161 BOLT, W/WASHER
013. [01] 91518-08221 BOLT, W/WASHER
014. [01] 90458-04051 KEY, WOODRUFF
016. [01] 94904-06950 BOLT, HEXAGON
017. [01] 94914-03430 O-RING

Include in #3:

09200-03680 as PUMP ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09200-03680  RE501033  PUMP ASSY, INJECTI
RE501033    JOHN DEERE PUMP ASSY, INJECTI




Information:


See the service manual for your engine for other adjusting procedures.
Rack Adjustment For Engines With NSFS
Rear Of Governor
1. Opening for variable power actuator.1. Remove the variable power actuator from the rear of the governor.2. Adjust the high power fuel setting using the standard fuel system setting procedure in the service manual.For the correct fuel setting specifications, see the Engine Information Plate or the FUEL SETTING AND RELATED INFORMATION FICHE.
6V7941 Compressor Assembly
Governor And Compressor
2. 6V7941 Compressor Assembly.3. Remove the 6V7941 Compressor Assembly (2) and replace the plug in the rear of the governor housing.
Variable Power Actuator
3. Rod. 4. Washered nut. 5. Jam nut. 6. Dust cover.4. Remove the dust cover (6) from the variable power actuator. Loosen the jam nut (5) on the rod (3). Tighten the washered nut (4) to put rod (3) in the fully retracted position.
Governor And Actuator
3. Rod. 4. Washered nut. 5. Jam nut. 7. Actuator.5. Install actuator (7) in governor housing opening (1).6. Move the governor control to the high idle position and hold or fasten the governor control in this position.7. Extend the actuator rod (3), by loosening the washered nut (4), to achieve a minimum dial indicator reading of 2.0 mm (.08 in.) less than the desired low power fuel setting.EXAMPLE: If the low power rack adjustment specification is 3.0 mm (.12 in.), the actuator rod (3) must be adjusted to obtain a dial indicator reading of 1.0 mm (.04 in.).8. Tighten the washered nut (4), to retract the actuator rod (3) and increase the dial indicator reading to the specified low power fuel setting.For the correct fuel setting specifications, see the Engine Information Plate or the FUEL SETTING AND RELATED INFORMATION FICHE.9. If the low power fuel setting is exceeded, repeat steps 7 and 8.10. Tighten the jam nut (5) on the actuator rod (3) and install the dust cover (6).3304 SMFS Air Only Actuator
See the service manual for your engine for other testing and adjusting procedures.
Rack Adjustment For Engines With Sleeve Metering Fuel System (SMFS)
1. Remove the variable power actuator (1) from the rear of the governor (2).2. Use the fuel setting procedure in the service manual and adjust the high power fuel setting screw.For the correct fuel setting specifications, see the Engine Information Plate or the FUEL SETTING AND RELATED INFORMATION FICHE.3. Install the variable power actuator (1).4. Remove the back cover (6) from the actuator (1) to expose the adjustment pin (5).5. Move the governor control shaft to the high idle position.6. Turn the adjustment pin (5) clockwise to adjust the variable power control rod (8) to the fully EXTENDED position.7. To adjust the low power setting, turn the adjustment pin (5) counterclockwise to retract rod (8). Retract the rod (8) until the rack setting is decreased to the specified setting.For the correct fuel setting specifications, see the Engine Information Plate or the FUEL SETTING AND RELATED INFORMATION FICHE.8. Replace cover (6) on the variable power actuator (6).
Governor And Variable Power Actuator
1. Variable power actuator. 2. Governor.
Governor And

Have questions with 09200-03680?





Group cross 09200-03680

Back to top