Information assy nzl
Nozzle:
0935005970
Rating:
KIT List:
| Governor assy, mec | No Application |
| Timer assy, automa | No Application |
| Pump assy, fuel fe | 1922900060 |
| Pump assy, fuel fe | 1922900060 |
| Body assy, injecti | 1904400380 |
Components :
| 001. | PUMP ASSY, INJECTI | 09200-02000 |
| 002. | GOVERNOR ASSY, MEC | 09130-05540 |
| 003. | LEVER SET | 09129-10381 |
| 004. | LEVER SET | 09129-10500 |
| 005. | COVER ASSY, GOVERN | 09145-00463 |
| 006. | TIMER ASSY, AUTOMA | 09180-03690 |
| 007. | PUMP ASSY, FUEL FE | 09210-02630 |
| 008. | PUMP ASSY, FUEL FE | 09210-03170 |
| 009. | COUPLING ASSY | 09250-01061 |
| 010. | BODY ASSY, INJECTI | 19010-00841 |
| 011. | COVER, BEARING | 09020-10430 |
Cross reference number
| Part num | Firm num | Firm | Name |
| 09200-02000 | ASSY Nzl | ||
| 22010-7812 | HINO | PUMP ASSY, INJECTI | |
| S2201-07813 | HINO | PUMP ASSY, INJECTI |
Information:
1. Move the transmission range selector (1) to NEUTRAL and the lock (2) to ON. 2. Move all scraper hydraulic controls to HOLD. 3. Apply the parking brake. 4. Move the cushion hitch control to LOCKDOWN. 5. Insert the key and turn the battery disconnect switch ON.
Never turn the disconnect switch OFF when the engine is running.
6. To prevent engine overspeed at startup, be sure the throttle lock button is OUT. 7. Push the accelerator pedal to just past ENGINE STOPPED detent. 8. Push in and turn the start switch to START. Release the switch when the engine starts.
After every 30 seconds of cranking, allow 2 minutes for the starting motor to cool.
9. If the engine oil pressure gauge doesn't register within 10 seconds, stop the engine by pulling up on the accelerator pedal. Have corrections made.10. Keep the engine at low idle until the systems are warm.11. Watch all gauges and indicators for correct readings before moving the machine.Cold Weather Starting
16°C (60°F) to -12°C (10°F)
1. Follow the steps under "Above 16°C (60°F)."
If the engine does not start after two attempts, use starting fluid. This will prevent excessive battery drain and starting motor overheating.
2. Use starting fluid by pushing the button under the start switch, at 2 second intervals, while cranking the engine. See "Ether Aids" under "Starting Aids."-12°C (10°F) to -26°C
Never turn the disconnect switch OFF when the engine is running.
6. To prevent engine overspeed at startup, be sure the throttle lock button is OUT. 7. Push the accelerator pedal to just past ENGINE STOPPED detent. 8. Push in and turn the start switch to START. Release the switch when the engine starts.
After every 30 seconds of cranking, allow 2 minutes for the starting motor to cool.
9. If the engine oil pressure gauge doesn't register within 10 seconds, stop the engine by pulling up on the accelerator pedal. Have corrections made.10. Keep the engine at low idle until the systems are warm.11. Watch all gauges and indicators for correct readings before moving the machine.Cold Weather Starting
16°C (60°F) to -12°C (10°F)
1. Follow the steps under "Above 16°C (60°F)."
If the engine does not start after two attempts, use starting fluid. This will prevent excessive battery drain and starting motor overheating.
2. Use starting fluid by pushing the button under the start switch, at 2 second intervals, while cranking the engine. See "Ether Aids" under "Starting Aids."-12°C (10°F) to -26°C