Fuel injectors
  1. Home
  2. denso
  3. #09010-06661

09010-06661 BODY ASSY, INJECTI Denso Cross


 

Information body assy, injecti

09010-06661 BODY ASSY, INJECTI
Rating:
40
Buy BODY ASSY, INJECTI 09010-06661 genuine, new aftermarket engine parts with delivery

Scheme ###:

BODY ASSY, INJECTI
000. [01] 09010-06661 BODY ASSY, INJECTI
001. [01] 09011-03650 HOUSING SUB-ASSY,
001-001. [03] 94904-30010 BOLT, STUD 94904-30010
002. [06] 09013-00300 HOLDER SUB-ASSY, D
003. [06] 09013-90050 O-RING
004. [06] 09013-60350 SPRING, DELIVERY V
006. [06] 09014-01750 VALVE SUB-ASSY, IN
007. [06] 09013-70120 GASKET, DELIVERY V
008. [06] 09015-03732 ELEMENT SUB-ASSY,
011. [06] 09043-60110 COVER, ELEMENT
011. [06] 09043-60181 COVER, ELEMENT
011. [06] 09043-60280 COVER, ELEMENT
012. [06] 94907-20780 RING, SNAP
013. [12] 09013-90170 O-RING
013. [12] 94914-01120 O-RING
014. [06] 09013-90040 O-RING 09013-90040
014. [06] 09013-90221 O-RING 09013-90221
016. [ C] 09043-80770 SHIM, ELEMENT HOLD 09043-80770
016. [ C] 09043-80780 SHIM, ELEMENT HOLD
016. [ C] 09043-80790 SHIM, ELEMENT HOLD
016. [ C] 09043-80800 SHIM, ELEMENT HOLD
016. [ C] 09043-80810 SHIM, ELEMENT HOLD
016. [ C] 09043-80820 SHIM, ELEMENT HOLD
016. [ C] 09043-80830 SHIM, ELEMENT HOLD
016. [ C] 09043-80840 SHIM, ELEMENT HOLD
016. [ C] 09043-80760 SHIM, ELEMENT HOLD
016. [ C] 09043-80750 SHIM, ELEMENT HOLD
016. [ C] 09043-80740 SHIM, ELEMENT HOLD
016. [ C] 09043-80080 SHIM, ELEMENT HOLD 09043-80080
016. [ C] 09043-80090 SHIM, ELEMENT HOLD
016. [ C] 09043-80100 SHIM, ELEMENT HOLD
016. [ C] 09043-80110 SHIM, ELEMENT HOLD
016. [ C] 09043-80120 SHIM, ELEMENT HOLD
016. [ C] 09043-80710 SHIM, ELEMENT HOLD 09043-80710
016. [ C] 09043-80720 SHIM, ELEMENT HOLD 09043-80720
016. [ C] 09043-80730 SHIM, ELEMENT HOLD
017. [12] 94901-17040 WASHER, STEEL PLAT
018. [12] 90258-10001 WASHER, SPRING 90258-10001
019. [12] 90160-10081 NUT, HEXAGON
020. [01] 09021-00541 RACK ASSY, CONTROL
020-001. [01] 09021-20340 RACK, CONTROL
020-002. [02] 94904-43200 BOLT
020-003. [01] 09021-95690 STOPPER
020-004. [02] 94901-33990 WASHER, PLATE, SK
020-005. [02] 90258-05001 WASHER, SPRING 90258-05001
021. [02] 09011-40060 BUSHING, CONTROL R
022. [01] 94908-20290 PIN, STRAIGHT
023. [01] 09036-70010 BUSHING, CONTROL R
024. [06] 09016-00130 SLEEVE SUB-ASSY, C
024. [06] 09016-00020 SLEEVE SUB-ASSY, C
025. [06] 09016-30060 SEAT, SPRING, UPR
026. [06] 09016-40230 SPRING, PUMP PLUNG
027. [06] 09016-50180 SEAT, SPRING, LWR
028. [06] 09017-00271 TAPPET SUB-ASSY,IN
028-001. [06] 09017-10280 TAPPET, INJECTION
028-001. [06] 09016-90180 BODY, INJECTION PU
028-002. [06] 09018-10170 ROLLER, INJECTION 09018-10170
028-002. [06] 09018-10240 ROLLER, INJECTION
028-003. [06] 09017-80060 BUSHING, INJECTION 09017-80060
028-004. [06] 09017-60080 PIN, INJECTION PUM 09017-60080
028-005. [06] 09017-50050 SLIDER
029. [01] 09019-11080 CAMSHAFT, INJECTIO
030. [01] 09036-10140 BEARING, CENTER
031. [09] 90258-06001 WASHER, SPRING 90258-06001
031. [05] 90258-06001 WASHER, SPRING 90258-06001
032. [02] 90015-06181 SCREW, SLOTTED OVA
032. [02] 94900-66510 SCREW
033. [01] 94910-10130 BEARING, ROLLER
034. [01] 09020-10620 COVER, BEARING
035. [01] 94915-02291 SEAL, OIL
036. [01] 09013-90060 O-RING
037. [2C] 09020-80210 PLATE, SHIM
037. [2C] 09020-80200 PLATE, SHIM
037. [2C] 09020-80190 PLATE, SHIM
037. [2C] 09020-80180 PLATE, SHIM
037. [2C] 09020-80170 PLATE, SHIM
037. [2C] 09020-80160 PLATE, SHIM
037. [2C] 09020-80150 PLATE, SHIM
038. [01] 09043-30010 RETAINER, BEARING
039. [04] 91518-06201 BOLT, W/WASHER
040. [03] 90160-06051 NUT, HEXAGON 90160-06051
041. [01] 09031-70070 PLUG, SCREW
042. [06] 09031-70060 PLUG, SCREW
043. [01] 09027-10380 PLATE, INJECTION P
044. [12] 90045-06121 SCREW, SLOTTED POL
046. [01] 94910-10170 BEARING, ROLLER
048. [02] 94918-00310 SCREW, HOLLOW 94918-00310
058. [01] 09031-00210 VALVE ASSY, OVERFL
059. [06] 09022-20070 WASHER, FUEL PIPE 09022-20070
061. [02] 94904-71790 BOLT, W/WASHER
063. [01] 94914-00380 O-RING
063. [01] 09010-60040 GASKET, FEED PUMP
065. [01] 09027-20260 GASKET, INJECTION
066. [01] 94901-80710 WASHER, COPPER PLA
067. [06] 94901-81500 WASHER, COPPER PLA
070. [01] 09011-80270 NEEDLE, TIMING

Include in #3:

09010-06661 as BODY ASSY, INJECTI
19100-01362

Cross reference number



Part num Firm num Firm Name
09010-06661    BODY ASSY, INJECTI




Information:


TIMING MARKS2. Remove the plug from the timing pin hole in fuel injection pump housing and install timing pin (1).
TIMING PIN INSTALLED
1. FT887 Timing Pin (Fabricated Tool).3. Remove the tachometer drive adapter shaft (2).
TACHOMETER DRIVE ADAPTER
2. Tachometer drive adapter shaft.4. Using puller group (3), remove the fuel injection pump camshaft drive gear as follows. Thread the 9S8528 Bolt Assembly into the fuel injection pump camshaft. Do not force the bolt assembly. It should thread easily. Install the 9S8527 Bolt by threading it into the drive gear. Then tighten the 9S8527 Bolt with a wrench until the gear "pops" loose. Remove the gear (4) and the tool setup.
9S8520 PULLER GROUP INSTALLED
3. 9S8520 Puller Group.
REMOVING GEAR
4. Gear.5. Remove retaining screw (5), washer (6), and automatic timing advance (7) from the engine camshaft.
TIMING ADVANCE
5. Retaining screw. 6. Washer. 7. Automatic timing advance.6. Install puller (8), with spacer (10) over the shaft in the camshaft and spacer (9) on spacer (10) as shown and remove the gear from the camshaft.
REMOVING GEAR (Typical Example)
8. 1P2321 Puller. 9. 8S5579 Spacer. 10. 9S9155 Spacer.Install Camshaft Gear
1. Heat the gear to a temperature of approximately 400° F (204° C) before installing on the camshaft.
Do not heat the gear with a torch. Do not heat the gear to a temperature of more than 600° F (315° C). Heating the gear with a torch or to a temperature of more than 600° F (315° C) may cause the two drive dowels for the automatic timing advance to loosen and come out of the gear.
2. Align slot in gear hub with the pin in the camshaft. Install the gear on the camshaft with timing mark on gear aligned with timing mark on crankshaft gear. Be sure the gear is completely seated against the shoulder of the camshaft.
TIMING MARKS
Do not drive the gear on the camshaft. Serious damage can result to camshaft or camshaft thrust pin.
3. Align holes in weights with dowels in gear and install the automatic timing advance.4. Align pin (11) in washer (6) with hole (12) in camshaft and install washer (6).
INSTALLING WASHER
6. Washer. 11. Pin. 12. Hole.5. Install retaining screw (5) and tighten to 108 36 lb. in. (124.5 41.5 cm.kg). Stake screw (5) in two places.
Stake retaining screw (5) carefully. Heavy blows on washer or retaining screw can force the shaft extension too far into the camshaft and eliminate all end clearance.
STAKING SCREW (Typical Example)
5. Retaining screw.6. After retaining screw (5) is staked, the gear and weight assembly requires .003 to .027 in. (0.08 to 0.69 mm) end clearance to prevent binding against the washer, camshaft end, or camshaft gear.7. Position the drive gear on the fuel injection pump camshaft.8. Install the tachometer drive adapter shaft and tighten the shaft retaining nut to 32 2 lb. ft. (4.4 0.3 mkg).9. Remove the timing pin from the fuel injection pump housing and install the plug in the timing hole.

Have questions with 09010-06661?





09016-90180 BODY, INJECTION PU 09016-90130 09016-90120 09016-90110 09016-90100
04203-00033 BODY ASSY, INJECTI 04203-20112 04203-30000 09010-01010 0901001180

Group cross 09010-06661

Back to top