09010-06520 BODY ASSY, INJECTI Denso Cross


 

Information body assy, injecti

09010-06520 BODY ASSY, INJECTI
Rating:
24
Buy BODY ASSY, INJECTI 09010-06520 genuine, new aftermarket engine parts with delivery

Scheme ###:

000. [01] 09010-06520 BODY ASSY, INJECTI
001. [01] 19011-03011 HOUSING KIT, INJEC 22190-87303-000
001-001. [03] 94904-30010 BOLT, STUD 90099-04071-000
001-002. [01] 09022-10070 UNION, INJECTION P
001-003. [01] 09022-10010 UNION, INJECTION P 22127-76010-000
001-003. [01] 09022-10310 UNION, INJECTION P
003. [04] 09013-10010 HOLDER, DELIVERY V 22131-77020-000
004. [04] 09013-60050 SPRING, DELIVERY V 22148-46010-000
005. [04] 09013-70010 GASKET, DELIVERY V 22149-76010-000
006. [04] 09014-00010 VALVE SUB-ASSY, IN 22104-77020-000
007. [04] 09015-02280 ELEMENT SUB-ASSY, 22105-87303-000
008. [04] 09015-60010 PINION, PLUNGER CO 22155-76010-000
009. [04] 09015-70010 SCREW, PLUNGER CON 22156-76010-000
010. [04] 09016-10160 SLEEVE, PLUNGER CO 22142-77020-000
010. [04] 09016-10330 SLEEVE, PLUNGER CO 22142-58230-000
011. [04] 09016-30010 SEAT, SPRING, UPR 22143-77020-000
011. [04] 09016-30191 SEAT, SPRING, UPR 22143-78150-000
012. [04] 09016-40060 SPRING, PUMP PLUNG 22144-87301-000
013. [04] 09016-50010 SEAT, SPRING, LWR 22145-77020-000
014. [04] 09017-00130 TAPPET SUB-ASSY,IN
014-001. [04] 09017-10173 TAPPET, INJECTION
014-002. [04] 09017-30010 BOLT, INJECTION PU 22134-77020-000
014-003. [04] 09017-40010 NUT, INJECTION PUM 22135-77020-000
014-004. [04] 09017-60010 PIN, INJECTION PUM 09017-60010-000
014-005. [04] 09017-80030 BUSHING, INJECTION
014-006. [04] 09018-10030 ROLLER, INJECTION
014-007. [04] 09017-50040 SLIDER
015. [04] 09018-90060 PLUG, INJECTION PU 22157-48023-000
015. [04] 09018-90090 PLUG, INJECTION PU 22157-87302-000
016. [01] 09019-10082 CAMSHAFT, INJECTIO 22146-56010-000
017. [02] 09019-30020 RING, CAMSHAFT ADJ 22147-77020-000
018. [6C] 09019-40060 PLATE, CAMSHAFT SH 22166-76010-000
018. [6C] 09019-40050 PLATE, CAMSHAFT SH 22165-76010-000
018. [6C] 09019-40040 PLATE, CAMSHAFT SH 22164-76010-000
018. [6C] 09019-40030 PLATE, CAMSHAFT SH 22163-76010-000
018. [6C] 09019-40020 PLATE, CAMSHAFT SH 22162-76010-000
018. [6C] 09019-40010 PLATE, CAMSHAFT SH 22161-76010-000
019. [01] 09020-10390 COVER, BEARING 22111-87303-000
020. [01] 09021-20441 RACK, CONTROL 22114-48030-000
021. [01] 09021-50011 SCREW, RACK GUIDE 22115-77020-000
021. [01] 09021-50060 SCREW, RACK GUIDE 22115-78140-000
022. [02] 09022-20070 WASHER, FUEL PIPE 22125-87301-000
023. [02] 09023-00031 PLATE SET, VALVE H 22102-77021-000
024. [01] 09024-00010 BLEEDER SUB-ASSY, 22150-67010-000
024-001. [01] 09024-10010 WASHER, AIR BLEEDE 22119-77020-000
024-002. [01] 09024-20010 NIPPLE, AIR BLEEDE 22118-77020-000
024-003. [01] 09024-30030 PACKING, AIR BLEED 22121-77020-000
024-004. [01] 09024-40010 SCREW, AIR BLEEDER 22117-77020-000
029. [01] 09027-01090 COVER SUB-ASSY, IN 22103-48030-000
029-002. [02] 09024-30030 PACKING, AIR BLEED 22121-77020-000
029-003. [02] 09027-60030 SCREW
029-006. [01] 09027-50182 PROCESSING DRAWING 22563-78050-000
029-007. [01] 09027-20210 GASKET, INJECTION 22153-78030-000
030. [01] 09020-60060 GASKET, BEARING CO 22195-68010-000
030. [01] 09020-60170 GASKET, BEARING CO 22195-87601-000
031. [03] 90160-06051 NUT, HEXAGON 94110-40600-000
032. [03] 90258-06001 WASHER, SPRING 94511-00600-000
033. [04] 91418-06201 BOLT, W/WASHER 91611-60620-000
034. [02] 94910-10120 BEARING, ROLLER 90091-30203-000
035. [01] 94914-03990 O-RING 90043-01065-000
036. [01] 94914-00380 O-RING 90099-14015-000
038. [01] 94918-00570 SCREW, HOLLOW
039. [01] 94918-00310 SCREW, HOLLOW 90099-18010-000
043. [01] 09045-30090 STAY, INJECTION PU 22177-87302-000
044. [02] 91410-08141 BOLT, W/WASHER 91611-40814-000

Include in #3:

09010-06520 as BODY ASSY, INJECTI

Cross reference number



Part num Firm num Firm Name
09010-06520    BODY ASSY, INJECTI




Information:


TIMING PIN HOLE PLUG (Typical Example)
1. Plug.2. Rotate the crankshaft CLOCKWISE (as viewed from front of engine) until the timing pin drops into the timing slot in the fuel injection pump camshaft.3. Disconnect wire (2) from fuel shut off solenoid.4. Remove the tachometer drive adapter housing (3).
WIRE AND HOUSING (Typical Example)
2. Wire. 3. Tachometer drive adapter housing.5. Use ratchet (4) and socket (5) to remove the tachometer drive adapter shaft.
REMOVING SHAFT
4. 8H8572 Ratchet. 5. 9S5031 Deep Well Socket.6. Using puller group (6), thread the 9S8528 Bolt Assembly into the camshaft. Do not force the bolt assembly. It should thread easily. Install the 9S8527 Bolt by threading it into the gear carrier or adapter. Then tighten the 9S8527 Bolt with a wrench until the gear carrier or adapter "pops" loose. Remove the 9S8520 Puller Group.
LOOSENING CAMSHAFT DRIVE GEAR
6. 9S8520 Puller Group.7. Remove the plug from the timing hole (8) in the front cover and insert bolt (7). The cover retaining bolt from hole (9) may be used.8. Rotate crankshaft CLOCKWISE (as viewed from front of engine) until bolt (7) threads into the timing gear and is centered in timing hole (8). With timing pin in slot in fuel pump camshaft and the bolt (7) through the front cover and threaded into the timing gear, the fuel injection pump camshaft is timed to the engine.
INSTALLING BOLT
7. 1D4539 Bolt [5/16 in. - 18 NC, 2.5 in. (63.5 mm) long]. 8. Timing hole. 9. Hole.9. Remove the fuel injection pump housing retaining bolts (10).
RETAINING BOLTS (Typical Example)
10. Retaining bolts (three).
REMOVING HOUSING (Typical Example)10. Attach a hoist and remove the fuel injection pump housing and governor as a unit, the weight is approx. 55 lbs. (23 kg).Install Fuel Injection Pump Housing and Governor
1. Attach a hoist and install the fuel injection pump housing and governor as a unit. Install the fuel injection pump housing retaining bolts.2. Install the tachometer drive adapter shaft and tighten shaft retaining nut to 32 2 lb. ft. (4.4 0.3 mkg).3. To check timing remove the timing pin and the bolt. Rotate the crankshaft two revolutions CLOCKWISE (as viewed from front of engine) and install the timing pin and bolt back in place. If the timing pin or bolt can not be installed, the fuel injection pump camshaft must be retimed.4. Remove the bolt (7) from the timing gear and install in hole (9). Install the plug into timing hole (8).5. Remove the timing pin from the timing slot in the fuel injection pump camshaft and install the plug in the timing hole.6. Install the tachometer drive adapter housing. Connect the wire to the fuel shut off solenoid.

Have questions with 09010-06520?





Group cross 09010-06520

Back to top