Fuel injectors
  1. Home
  2. denso
  3. #09010-03800

09010-03800 BODY ASSY, INJECTI Denso Cross


 

Information body assy, injecti

09010-03800 BODY ASSY, INJECTI
Rating:
53
Buy BODY ASSY, INJECTI 09010-03800 genuine, new aftermarket engine parts with delivery

Scheme ###:

BODY ASSY, INJECTI
000. [01] 09010-03800 BODY ASSY, INJECTI 30061-83500
001. [01] 19011-01620 HOUSING KIT, INJEC
001-001. [03] 94904-30010 BOLT, STUD ME702091
002. [06] 09013-10020 HOLDER, DELIVERY V 09013-10020
003. [06] 09013-60010 SPRING, DELIVERY V MM500666
004. [06] 09013-70010 GASKET, DELIVERY V ME022084
005. [06] 09014-00021 VALVE SUB-ASSY, IN ME022085
006. [06] 09015-00390 ELEMENT SUB-ASSY, 09015-00390
007. [06] 09015-60010 PINION, PLUNGER CO ME702058
008. [06] 09015-70010 SCREW, PLUNGER CON ME702059
009. [06] 09016-10160 SLEEVE, PLUNGER CO ME022134
009. [06] 09016-10330 SLEEVE, PLUNGER CO ME702060
010. [06] 09016-30010 SEAT, SPRING, UPR ME702061
010. [06] 09016-30191 SEAT, SPRING, UPR ME736080
011. [06] 09016-40010 SPRING, PUMP PLUNG ME702062
012. [06] 09016-50010 SEAT, SPRING, LWR ME702063
013. [06] 09017-00020 TAPPET SUB-ASSY,IN 09017-00020
013. [06] 09017-00130 TAPPET SUB-ASSY,IN ME702064
013-001. [06] 09017-10173 TAPPET, INJECTION
013-001. [06] 09016-90130 BODY, INJECTION PU ME702065
013-001. [06] 09016-90110 BODY, INJECTION PU
013-002. [06] 09017-30010 BOLT, INJECTION PU ME702066
013-003. [06] 09017-40010 NUT, INJECTION PUM ME702067
013-004. [06] 09017-60010 PIN, INJECTION PUM ME702068
013-005. [06] 09017-80030 BUSHING, INJECTION ME702069
013-006. [06] 09018-10030 ROLLER, INJECTION ME702070
013-007. [06] 09017-50040 SLIDER ME736247
014. [01] 09020-60030 GASKET, BEARING CO ME728972
015. [06] 09018-90090 PLUG, INJECTION PU ME703276
015. [06] 09018-90060 PLUG, INJECTION PU ME702071
016. [01] 09019-10421 CAMSHAFT, INJECTIO 09019-10420
017. [01] 94915-00570 SEAL, OIL ME022140
018. [02] 94910-10120 BEARING, ROLLER ME702096
019. [02] 09019-30020 RING, CAMSHAFT ADJ ME702074
020. [6C] 09019-40150 PLATE, CAMSHAFT SH ME703273
020. [6C] 09019-40140 PLATE, CAMSHAFT SH ME703272
020. [6C] 09019-40060 PLATE, CAMSHAFT SH ME022103
020. [6C] 09019-40050 PLATE, CAMSHAFT SH ME022102
020. [6C] 09019-40040 PLATE, CAMSHAFT SH ME022101
020. [6C] 09019-40030 PLATE, CAMSHAFT SH ME022100
020. [6C] 09019-40020 PLATE, CAMSHAFT SH ME022099
020. [6C] 09019-40010 PLATE, CAMSHAFT SH ME702075
021. [01] 94914-00380 O-RING ME702097
024. [01] 09020-10270 COVER, BEARING
025. [01] 09021-20010 RACK, CONTROL ME702079
026. [01] 09021-50060 SCREW, RACK GUIDE ME728163
026. [01] 09021-50011 SCREW, RACK GUIDE ME702080
027. [02] 09022-20070 WASHER, FUEL PIPE ME702217
028. [01] 94918-00310 SCREW, HOLLOW ME702236
029. [03] 09023-00031 PLATE SET, VALVE H ME702082
030. [01] 09024-00010 BLEEDER SUB-ASSY, ME702083
030-001. [01] 09024-10010 WASHER, AIR BLEEDE ME702102
030-002. [01] 09024-20010 NIPPLE, AIR BLEEDE ME022094
030-003. [01] 09024-30030 PACKING, AIR BLEED ME702057
030-004. [01] 09024-40010 SCREW, AIR BLEEDER MM501930
032. [01] 09036-10040 BEARING, CENTER ME702088
033. [02] 94900-66550 SCREW ME736044
034. [02] 94901-81030 WASHER, COPPER PLA ME702094
036. [02] 09025-10010 WASHER, INJECTION ME702595
037. [01] 94918-00060 SCREW, HOLLOW ME702598
038. [01] 94914-00380 O-RING ME702097
041. [01] 09027-00622 COVER SUB-ASSY, IN 09027-00621
041. [01] 09027-00941 COVER SUB-ASSY, IN ME703939
041-002. [02] 09024-30030 PACKING, AIR BLEED ME702057
041-003. [02] 09027-60030 SCREW ME703028
041-008. [01] 09027-50083 PROCESSING DRAWING ME702602
041-009. [01] 09027-20220 GASKET, INJECTION ME702085
043. [04] 94904-71360 BOLT, W/WASHER ME022507
045. [02] 94901-81120 WASHER, COPPER PLA
046. [01] 94918-00420 SCREW, HOLLOW

Include in #3:

09010-03800 as BODY ASSY, INJECTI
19000-02580

Cross reference number



Part num Firm num Firm Name
09010-03800  30061-8350  BODY ASSY, INJECTI
30061-83500    MITSUBISHI BODY ASSY, INJECTI




Information:

Fuel Injection Nozzles
Disassembly of Fuel Injection Nozzles
Inspection of Fuel Injection Nozzles
Check each fuel injection nozzle for the following, and if defects are found, repair or replace the fuel injection nozzle.(1) Inspection of injection start pressure(a) Install each fuel injection nozzle on the nozzle tester, and move the handle up and down to release air.(b) Operate the handle of the tester at a rate of about 1 stroke per second, and read the indication on the pressure gage. The indication rises slowly, and the indicator oscillates during spraying. To obtain the injection start pressure value, read the indication when the indicator starts to oscillate.
Inspection of fuel injection nozzle valve opening(c) If the injection start pressure deviates significantly from the standard value, disassemble the fuel injection nozzle, and make an adjustment by changing the washer thickness. 0.1 mm [0.0039 in.] thickness of shims will change the injection pressure 0.98 Mpa (10 kgf/cm2 [142 psi]. The shims are available in 10 different thickness from 1.25 to 1.70 mm [0.0492 to 0.0669 in.] increment of 0.05 mm [0.0020 in.]
Never tap the tip of the nozzle tip when removing the nozzle tip.
Replacement of fuel injection nozzle tip(2) Inspection of fuel injection nozzle spray pattern(a) When inspecting each fuel injection nozzle with the nozzle tester, also check the nozzle for clogs, spray pattern and leakage.(b) Make sure that the fuel is sprayed straight from the nozzle when the handle of the tester is operated at a rate of about 1 stroke per second.
Inspection of spray pattern of fuel injection nozzle(3) Cleaning and replacement of faulty nozzles(a) Loosen the nozzle retaining nut, remove the nozzle tip, and clean the needle valve and body.
Never tap the tip of the nozzle tip when removing the nozzle tip.
(b) Use a fresh cleaning solution to clean the needle valve and body. After cleaning, assemble the needle valve and body in clean diesel fuel. The needle valve and body are precision finished. Handle them carefully, and do not change the combination of parts.
Cleaning of fuel injection nozzle tip(c) Tighten the nozzle retaining nut on the nozzle tip to the specified torque.(d) If the spray pattern is still not acceptable after adjustment and cleaning, replace the nozzle tip. (a) Never touch the sliding surface of the needle valve.(b) When installing a new nozzle tip, remove the seal film (synthetic resin film), and slide needle valve in the nozzle in a fresh cleaning solution to remove anti-rust oil coating thoroughly from the new nozzleReassembly of Fuel Injection Nozzles

Have questions with 09010-03800?





09016-90130 BODY, INJECTION PU 09016-90120 09016-90110 09016-90100 09016-90070
04203-00033 BODY ASSY, INJECTI 04203-20112 04203-30000 09010-01010 0901001180

Group cross 09010-03800

Back to top