Information pump assy, injecti
Nozzle:
0935000900
Rating:
KIT List:
| Body assy, injecti | 1904400360 |
| Governor assy, mec | 1908900150 |
| Pump assy, fuel fe | 1922900060 |
Components :
| 001. | PUMP ASSY, INJECTI | 09000-04980 |
| 002. | BODY ASSY, INJECTI | 09010-01581 |
| 003. | GOVERNOR ASSY, MEC | 09080-01381 |
| 004. | PUMP ASSY, FUEL FE | 09210-00412 |
| 005. | COUPLING ASSY | 09240-00043 |
Scheme ###:
| 000. | [01] | 09000-04981 | PUMP ASSY, INJECTI | 6 074 1103 30 |
| 007. | [01] | 09010-01581 | BODY ASSY, INJECTI | 22130-1070 |
| 008. | [01] | 09080-01381 | GOVERNOR ASSY, MEC | 6 075 1301 91 |
| 009. | [06] | 90017-06141 | SCREW, SLOTTED OVA | 6 056 1320 50 |
| 011. | [01] | 91518-08221 | BOLT, W/WASHER | 22815-1190A |
| 013. | [01] | 09001-80220 | COVER, CONTROL RAC | 22114-1050A |
| 014. | [01] | 09255-00060 | BLOCK SUB-ASSY, CO | 6 056 1328 00 |
| 015. | [01] | 09001-20010 | NUT, TIMER ROUND | 22353-1050A |
| 016. | [01] | 94913-00050 | KEY, WOODRUFF | 22891-1040A |
| 017. | [01] | 90258-12001 | WASHER, SPRING | 22873-1310A |
| 018. | [01] | 09210-00412 | PUMP ASSY, FUEL FE | 6 302 1500 11 |
| 019. | [01] | 09006-10011 | COVER, PRIMING PUM | 6 053 1552 60 |
| 022. | [01] | 09240-00043 | COUPLING ASSY | 22610-1090A |
| 023. | [01] | 09243-60040 | COUPLING, INJECTIO | 22612-1100A |
Cross reference number
| Part num | Firm num | Firm | Name |
| 09000-04980 | PUMP ASSY, INJECTI | ||
| 6 074 1103 30 | HINO | PUMP ASSY, INJECTI |
Information:
(1) End play for shaft (new) ... 0.114 0.038 mm (.0045 .0015 in) Maximum permissible end play (worn) ... 0.20 mm (.008 in)(2) Thickness of thrust bearing (where thrust rings contact bearing) ... 5.36 0.03 mm (.211 .001 in)(3) Diameter of shaft (new) ... 15.997 to 16.005 mm (.6298 to .6301 in) Bore in the bearing (new) ... 16.035 to 16.043 mm (.6313 to .6316 in)Maximum permissible clearance between bearing and shaft (worn) ... 0.05 mm (.002 in)(4) Maximum permissible gap of oil seal ring, measured in bore of housing ... 0.25 mm (.010 in)(5) Install the compressor wheel (at room temperature) as follows: a. Put compressor wheel on the shaft.b. Put a small amount of clean engine oil on the threads.c. Tighten the