Information delivery-valve assembly
BOSCH
9 443 610 398
9443610398
ZEXEL
141110-6620
1411106620
NIIGATA-URAWA
3E647060A
3e647060a
Rating:
Include in ###:
Cross reference number
Zexel num
Bosch num
Firm num
Name
141110-6620
3E647060A NIIGATA-URAWA
DELIVERY-VALVE ASSEMBLY
K 28FE DELIVERY VALVE DV(PF-W for marine) DV
K 28FE DELIVERY VALVE DV(PF-W for marine) DV
141110-6620
3E647060A NIIGATA-TEKKOU
DELIVERY-VALVE ASSEMBLY
K 28FE DELIVERY VALVE DV(PF-W for marine) DV
K 28FE DELIVERY VALVE DV(PF-W for marine) DV
141110-6620
3E647060A
DELIVERY-VALVE ASSEMBLY
K 28FE DELIVERY VALVE DV(PF-W for marine) DV
K 28FE DELIVERY VALVE DV(PF-W for marine) DV
Information:
The diagnostic lamp, on the truck dashboard, can be used to communicate status or operation problems of the electronic control system.Trucks With Cruise
The dash mounted cruise switches are used to interrogate the ECM for system status. With the cruise switch in the "off" position, hold the set/resume switch in the resume position until "check engine" light begins to flash. The sequence of flashes represents the system diagnostic message. The first sequence of flashes adds up to the first digit of the fault code. After a one second pause, a second sequence of flashes will occur which represents the second digit of the fault code. Any additional fault codes will follow, after a pause, and will be displayed in the same manner.Trucks Without Cruise
If cruise control switches are not installed or if their configuration (such as a GM type switch) does not permit their usage for checking diagnostic codes, then a push button momentary ON switch should be installed between Pin 3 of the vehicle connector P7 and engine ground.Faults With Throttle Response
The vehicle should be driven to a dealer for service ONLY if the engine oil pressure gauge indicates normal engine oil pressure and engine fuel pressure is within the normal range.Faults Without Throttle Response
If the check engine light is on and the engine does not respond to changes in throttle position, the vehicle should be driven to a dealer ONLY if the oil pressure gauge indicates normal engine oil pressure and engine fuel pressure is within the normal range.If equipped, turn on the cruise on/off switch and operate the vehicle using the set/resume cruise control switch to raise and lower the engine rpm.The cruise control mode is operational from 0 km/h (mph) up to the vehicle speed limit (VSL) when the 3406B (PEEC III) control unit does not respond to changes in throttle position. Maximum engine rpm will be the programmed engine rpm at the vehicle speed limit (VSL). Cruise control must be reselected after each gear change.
The dash mounted cruise switches are used to interrogate the ECM for system status. With the cruise switch in the "off" position, hold the set/resume switch in the resume position until "check engine" light begins to flash. The sequence of flashes represents the system diagnostic message. The first sequence of flashes adds up to the first digit of the fault code. After a one second pause, a second sequence of flashes will occur which represents the second digit of the fault code. Any additional fault codes will follow, after a pause, and will be displayed in the same manner.Trucks Without Cruise
If cruise control switches are not installed or if their configuration (such as a GM type switch) does not permit their usage for checking diagnostic codes, then a push button momentary ON switch should be installed between Pin 3 of the vehicle connector P7 and engine ground.Faults With Throttle Response
The vehicle should be driven to a dealer for service ONLY if the engine oil pressure gauge indicates normal engine oil pressure and engine fuel pressure is within the normal range.Faults Without Throttle Response
If the check engine light is on and the engine does not respond to changes in throttle position, the vehicle should be driven to a dealer ONLY if the oil pressure gauge indicates normal engine oil pressure and engine fuel pressure is within the normal range.If equipped, turn on the cruise on/off switch and operate the vehicle using the set/resume cruise control switch to raise and lower the engine rpm.The cruise control mode is operational from 0 km/h (mph) up to the vehicle speed limit (VSL) when the 3406B (PEEC III) control unit does not respond to changes in throttle position. Maximum engine rpm will be the programmed engine rpm at the vehicle speed limit (VSL). Cruise control must be reselected after each gear change.