105672-5160 ZEXEL 9 420 616 891 BOSCH AUTOM. ADVANCE MECHANISM 9420616891 1056725160 me731529


 

Information autom. advance mechanism

BOSCH 9 420 616 891 9420616891
ZEXEL 105672-5160 1056725160
MITSUBISHI ME731529 me731529
105672-5160 AUTOM. ADVANCE MECHANISM
Rating:
45
Buy AUTOM. ADVANCE MECHANISM 105672-5160 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

1. [1] 156720-1120 TIMING-DEVICE HOUSING
2. [1] 156721-1500 FLANGE BUSHING
3. [2] 156723-0300 ECCENTRIC DISC
3. [2] 156723-0300 ECCENTRIC DISC
4. [2] 156723-0400 ECCENTRIC DISC
4. [2] 156723-0400 ECCENTRIC DISC
5. [1] 156730-8120 FLYWEIGHT ASSEMBLY
5/1. [2] 156722-1820 FLYWEIGHT
5/1. [2] 156722-1820 FLYWEIGHT
5/2. [4] 156727-1000 SPRING SEAT
5/2. [4] 156727-1000 SPRING SEAT
5/3. [4] 156727-1000 SPRING SEAT
5/3. [4] 156727-1000 SPRING SEAT
5/4. [4] 156754-9400 COMPRESSION SPRING
5/4. [4] 156754-9400 COMPRESSION SPRING
5/5. [4] 156754-9500 COMPRESSION SPRING
5/5. [4] 156754-9500 COMPRESSION SPRING
5/6. [4] 156809-0300 LOCKING WASHER
5/6. [4] 156809-0300 LOCKING WASHER
5/7. [2] 156726-1000 PIN
5/8/1. [0] 156728-0800 SHIM D19&15T0.1
5/8/1. [0] 156728-0900 SHIM D19&15T0.3
5/8/1. [0] 156728-1000 SHIM D19&15T0.5
5/8/1. [0] 156728-1000 SHIM D19&15T0.5
5/8/1. [0] 156728-1100 SHIM D19&15T1.0
5/8/1. [0] 156728-2000 SHIM D19&15T0.4
5/8/1. [0] 156728-2100 SHIM D19&15T0.7
5/8/1. [0] 156728-2400 SHIM D19&15T0.6
5/8/1. [0] 156728-2500 SHIM D19&15T0.8
5/8/1. [0] 156728-2600 SHIM D19&15T0.9
5/9/1. [0] 156728-1200 SHIM D14&10.6T0.1
5/9/1. [0] 156728-1300 SHIM D14&10.6T0.3
5/9/1. [0] 156728-1300 SHIM D14&10.6T0.3
5/9/1. [0] 156728-1400 SHIM D14&10.6T0.5
5/9/1. [0] 156728-1500 SHIM D14&10.6T1.0
5/9/1. [0] 156728-2200 SHIM D14&10.6T0.4
5/9/1. [0] 156728-2300 SHIM D14&10.6T0.7
5/9/1. [0] 156728-2700 SHIM D14&10.6T0.6
5/9/1. [0] 156728-2800 SHIM D14&10.6T0.8
5/9/1. [0] 156728-2900 SHIM D14&10.6T0.9
5/10. [4] 156808-0800 SPACER BUSHING
13. [1] 156729-1720 COVER
13/2. [1] 139635-0100 PACKING RING
13/3. [1] 156117-0100 O-RING
30. [1] 029321-4010 LOCKING WASHER
31. [1] 131325-3201 UNION NUT
33. [2] 026508-1240 GASKET D11.9&8.2T1
34. [2] 156115-0100 CAPSULE

Include in #1:

101607-6221 as AUTOM. ADVANCE MECHANIS

Cross reference number

Zexel num
Bosch num
Firm num
Name
105672-5160 
9 420 616 891 
NP-EP/SAG1080-1390B6/L 
ME731529  MITSUBISHI
AUTOM. ADVANCE MECHANISM
K




Information:

Part of the 8S2245 Cleaning Group.Start By:a. remove valve covers 1. Use tooling (A), and disconnect fuel line (1) at each end. Remove the fuel line from the engine. 2. Use tool (B), and remove retainer (2) from the adapter.3. Remove the fuel injection nozzles with tooling (C) as follows:a. Install the 6V6983 Adapter and the 8T3199 Screw into nozzle assembly (3).b. Install the 8T3198 Tube over the 8T3199 Screw.c. Use the 1B4206 Nut on the 8T3199 Screw.d. Use the 1B4206 Nut on the 8T3199 Screw to pull the fuel injection nozzle from the adapter.4. Remove compression seal (4) and carbon dam seal (8) from fuel injection nozzle (3).5. Use tool (D), and remove adapter (6) from the cylinder head.6. Remove gasket (7) and seal (5) from adapter (6). The following steps are for installation of the fuel injection nozzles and adapters.7. Use tool (E) to clean the bore in adapter (6). Use an open end wrench or tap driver to turn tool (E).8. Inspect seal (5) for damage or wear. Replace the seal if necessary.9. Put washer (7) and seal (5) in position on adapter (6).10. Put liquid soap in the bores of the cylinder head and on seals (5) in the adapters.11. Put 5P3931 Anti-Seize Compound on the threads of adapter (6), and install the adapter in the cylinder head assembly.12. Use tool (D), and tighten the adapter to a torque of 205 14 N m (150 10 lb.ft.).
Make sure the correct compression seal washer (4) is used when the nozzle assembly is installed in the adapter. Only copper washers are to be used with this adapter.
13. Install compression seal washer (4), and use tool (F) to install carbon dam seal (8) on the fuel injection nozzle.14. Put fuel injection nozzle (3) in position in the adapter, and install retainer (2).15. Use tool (B) to tighten retainer (2) to a torque of 48 7 N m (35 5 lb.ft.).16. Install fuel line (1). Tighten the nuts on the fuel line with tooling (A) to a torque of 40 7 N m (30 5 lb.ft.).End By:a. install valve covers

Have questions with 105672-5160?





Group cross 105672-5160 ZEXEL

Mitsubishi 

9 420 616 001 
NP-EP/SAG1050-1400B6/L 
ME730783 
AUTOM. ADVANCE MECHANISM
 
ME730826 
AUTOM. ADVANCE MECHANISM
9 420 616 002 
NP-EP/SAG1130-1350B3.5/L 
ME730834 
AUTOM. ADVANCE MECHANISM
9 420 615 555 
NP-EP/SAG900-1450B5EL 
 
AUTOM. ADVANCE MECHANISM

Mitsubishi 

9 420 615 629 
NP-EP/SAG1080-1390B6/L 
ME730892 
AUTOM. ADVANCE MECHANISM
9 420 615 588 
NP-EP/SAG1130-1350B3.5/L 
ME730888 
AUTOM. ADVANCE MECHANISM
105672-5160  
9 420 616 891 
NP-EP/SAG1080-1390B6/L 
ME731529 
AUTOM. ADVANCE MECHANISM
9 420 615 589 
NP-EP/SAG1100-1450B6/L 
ME731530 
AUTOM. ADVANCE MECHANISM
9 420 615 590 
NP-EP/SAG1100-1450B6/L 
ME731535 
AUTOM. ADVANCE MECHANISM
9 420 616 003 
NP-EP/SAG1130-1350B3.5/L 
ME731531 
AUTOM. ADVANCE MECHANISM
Back to top