105691-3661 ZEXEL 9 420 616 028 BOSCH AUTO;TIMING DEVICE 9420616028 1056913661 me738874

Information auto;timing device

BOSCH 9 420 616 028 9420616028

ZEXEL 105691-3661 1056913661

MITSUBISHI ME738874 me738874

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy AUTO;TIMING DEVICE 105691-3661 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

1.	[1]	156995-0321	AUTO;TIMING DEVICE
1/1.	[1]	156900-8200	FLANGE BUSHING
1/2.	[1]	156901-6920	TIMING-DEVICE HOUSING
1/3.	[6]	139006-2700	BLEEDER SCREW
1/5.	[2]	156904-0700	ECCENTRIC DISC
1/5.	[2]	156904-0700	ECCENTRIC DISC
1/6.	[2]	156904-0100	ECCENTRIC DISC
1/6.	[2]	156904-0100	ECCENTRIC DISC
1/7.	[1]	156903-1120	SLOTTED WASHER
1/8.	[2]	156907-2820	PLATE
1/9.	[2]	156910-2000	PIN
1/10.	[4]	156908-4800	COMPRESSION SPRING
1/10.	[4]	156908-4800	COMPRESSION SPRING
1/11.	[4]	156909-0000	SLOTTED WASHER
1/11.	[4]	156909-0000	SLOTTED WASHER
1/12.	[4]	156707-0000	SLOTTED WASHER
1/12.	[4]	156707-0000	SLOTTED WASHER
1/13.	[4]	156913-7400	LOCKING WASHER
1/13.	[4]	156913-7400	LOCKING WASHER
1/14.	[1]	156905-1400	CYLINDER
1/15.	[2]	156906-0300	PUMP PLUNGER
1/16.	[2]	156906-0300	PUMP PLUNGER
1/17.	[1]	156902-0820	COVER
1/17/3.	[1]	139799-0100	O-RING
1/19.	[6]	010235-0820	HEX-SOCKET-HEAD CAP SCREW
1/21.	[1]	156913-0900	CAPSULE
1/35.	[4]	156913-7300	SHIM
1/35.	[4]	156913-7300	SHIM
2.	[1]	479770-1102	PULSE GENERATOR
3.	[1]	029201-6150	UNION NUT
4.	[1]	139316-0000	PLAIN WASHER D25&16.5T5
5.	[1]	156913-7100	PLATE
6.	[2]	020018-2070	BLEEDER SCREW M8P1.25L20 7T
8.	[2]	014020-8140	PLAIN WASHER D16&8.5T1.2
10.	[1]	134563-2300	WOODRUFF KEY
11.	[1]	156913-3900	CAP
12.	[1]	139756-0000	O-RING
13.	[2]	012206-1220	FLAT-HEAD SCREW
16.	[1]	156809-0100	UNION NUT
17.	[1]	156809-0000	LOCKING WASHER

Include in #1:

106873-7121 as AUTOM. ADVANCE MECHANIS

Cross reference number

Zexel num

Bosch num

Firm num

Name

105691-3661

9 420 616 028

ME738874 MITSUBISHI

AUTO;TIMING DEVICE
K

Information:

2. Remove six bolts (1) on radiator cover (2). 3. Loosen clamp (3) and clamp (4) and disconnect hoses. Remove two bolts (5) and remove fan guard (6). 4. Disconnect hose (8) and hose (9) from bottom of radiator y-pipe. Remove eight bolts (7) from fan shroud and move shroud toward engine to allow access to fan. 5. Remove six bolts (10) remove fan and spacer (11). Remove shroud assembly (12). 6. Loosen two bolts (13) on alternator to remove belts (14). Remove four bolts (15) on fan drive (16) and remove fan drive. The following steps are for the installation of the fan drive7. Place fan drive (16) in position and install four bolts (15).8. Place belts (14) on fan drive pulley and around the alternator pulley. Use a belt tension gauge such as a Borroughs BT-33-95 Gauge to check the belt tension. Adjust a new belt to a gauge reading of 534 22 N m (120 5 lb ft). Adjust a used belt to a gauge reading of 400 44 N m (90 10 lb ft). Tighten two bolts (13) on the alternator when belts are under tension.9. Place shroud assembly (12) into position against the engine and install fan and spacer.10. Mount shroud assembly (12) to brackets around radiator with eight bolts (7).11. Connect hoses (8) and (9) to proper position on y-pipe at the bottom of the radiator.12. Install fan guard (6) with two bolts (5).13. Connect two hoses with clamps (3) and (4).14. Install radiator cover (2) with six bolts (1).15. Fill cooling system. See the Maintenance Manual.Disassemble And Assemble Fan Drive
Start By:a. remove fan drive 1. Remove dust cover (1). 2. Remove bolt (2) and plate (3). Remove six bolts (4) and remove pulley (5) off of hub (10). Slide hub off of bracket (6). 3. Remove cone bearing (7), cup bearing (8), spacer (9), cup bearing (11), cone bearing (13), seal (12) and spacer (14) out of hub. The following steps are for the assembly of the fan drive.4. Install spacer (14) onto bracket (6).5. Install cup bearing (11) and cone bearing (13) into hub (10).6. Install seal (12) as shown in Illustration.7. Install spacer (9), cup bearing (8) and cone bearing (7) into hub (10).8. Place hub assembly onto bracket shaft.9. Install plate (3) and bolt (2) into shaft and place dust cover (1) on shaft.10. Install pulley (5).End By:a. install fan drive