105691-3650 ZEXEL 9 420 615 615 BOSCH AUTO;TIMING DEVICE 9420615615 1056913650 me731623

Information auto;timing device

BOSCH 9 420 615 615 9420615615

ZEXEL 105691-3650 1056913650

MITSUBISHI ME731623 me731623

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy AUTO;TIMING DEVICE 105691-3650 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

1.	[1]	156995-0220	AUTO;TIMING DEVICE
1/1.	[1]	156900-8300	FLANGE BUSHING
1/2.	[1]	156901-6820	TIMING-DEVICE HOUSING
1/3.	[6]	139006-2700	BLEEDER SCREW
1/5.	[2]	156904-0700	ECCENTRIC DISC
1/5.	[2]	156904-0700	ECCENTRIC DISC
1/6.	[2]	156904-0100	ECCENTRIC DISC
1/6.	[2]	156904-0100	ECCENTRIC DISC
1/7.	[1]	156903-1120	SLOTTED WASHER
1/8.	[2]	156907-2820	PLATE
1/9.	[2]	156910-2000	PIN
1/10.	[4]	156908-4800	COMPRESSION SPRING
1/10.	[4]	156908-4800	COMPRESSION SPRING
1/11.	[4]	156909-0000	SLOTTED WASHER
1/11.	[4]	156909-0000	SLOTTED WASHER
1/12.	[4]	156707-0000	SLOTTED WASHER
1/12.	[4]	156707-0000	SLOTTED WASHER
1/13.	[4]	156913-7400	LOCKING WASHER
1/13.	[4]	156913-7400	LOCKING WASHER
1/14.	[1]	156905-1400	CYLINDER
1/15.	[2]	156906-0300	PUMP PLUNGER
1/16.	[2]	156906-0300	PUMP PLUNGER
1/17.	[1]	156902-0820	COVER
1/17/3.	[1]	139799-0100	O-RING
1/19.	[6]	010235-0820	HEX-SOCKET-HEAD CAP SCREW
1/21.	[1]	156913-0900	CAPSULE
1/35.	[4]	156913-7300	SHIM
1/35.	[4]	156913-7300	SHIM
2.	[1]	479770-0900	PULSE GENERATOR
3.	[1]	029201-6150	UNION NUT
4.	[1]	139316-0000	PLAIN WASHER D25&16.5T5
5.	[1]	156913-7100	PLATE
6.	[2]	020018-2070	BLEEDER SCREW M8P1.25L20 7T
8.	[2]	014020-8140	PLAIN WASHER D16&8.5T1.2
10.	[1]	134563-2300	WOODRUFF KEY
11.	[1]	156913-3900	CAP
12.	[1]	139756-0000	O-RING
13.	[2]	012206-1220	FLAT-HEAD SCREW
16.	[1]	156809-0100	UNION NUT
17.	[1]	156809-0000	LOCKING WASHER

Include in #1:

106673-2820 as AUTOM. ADVANCE MECHANIS

Cross reference number

Zexel num

Bosch num

Firm num

Name

105691-3650

9 420 615 615

ME731623 MITSUBISHI

AUTO;TIMING DEVICE
K

Information:

3306 New Scroll Fuel System (NSFS)
See the service manual for your engine for other adjusting procedures.
Rack Adjustment For Engines With NSFS
Rear Of Governor
1. Opening for variable power actuator.1. Remove the variable power actuator from the rear of the governor.2. Adjust the high power fuel setting using the standard fuel system setting procedure in the service manual.For the correct fuel setting specifications, see the Engine Information Plate or the FUEL SETTING AND RELATED INFORMATION FICHE.
6V7941 Compressor Assembly
Governor And Compressor
2. 6V7941 Compressor Assembly.3. Remove the 6V7941 Compressor Assembly (2) and replace the plug in the rear of the governor housing.
Variable Power Actuator
3. Rod. 4. Washered nut. 5. Jam nut. 6. Dust cover.4. Remove the dust cover (6) from the variable power actuator. Loosen the jam nut (5) on the rod (3). Tighten the washered nut (4) to put rod (3) in the fully retracted position.
Governor And Actuator
3. Rod. 4. Washered nut. 5. Jam nut. 7. Actuator.5. Install actuator (7) in governor housing opening (1).6. Move the governor control to the high idle position and hold or fasten the governor control in this position.7. Extend the actuator rod (3), by loosening the washered nut (4), to achieve a minimum dial indicator reading of 2.0 mm (.08 in.) less than the desired low power fuel setting.EXAMPLE: If the low power rack adjustment specification is 3.0 mm (.12 in.), the actuator rod (3) must be adjusted to obtain a dial indicator reading of 1.0 mm (.04 in.).8. Tighten the washered nut (4), to retract the actuator rod (3) and increase the dial indicator reading to the specified low power fuel setting.For the correct fuel setting specifications, see the Engine Information Plate or the FUEL SETTING AND RELATED INFORMATION FICHE.9. If the low power fuel setting is exceeded, repeat steps 7 and 8.10. Tighten the jam nut (5) on the actuator rod (3) and install the dust cover (6).3304 SMFS Air Only Actuator
See the service manual for your engine for other testing and adjusting procedures.
Rack Adjustment For Engines With Sleeve Metering Fuel System (SMFS)
1. Remove the variable power actuator (1) from the rear of the governor (2).2. Use the fuel setting procedure in the service manual and adjust the high power fuel setting screw.For the correct fuel setting specifications, see the Engine Information Plate or the FUEL SETTING AND RELATED INFORMATION FICHE.3. Install the variable power actuator (1).4. Remove the back cover (6) from the actuator (1) to expose the adjustment pin (5).5. Move the governor control shaft to the high idle position.6. Turn the adjustment pin (5) clockwise to adjust the variable power control rod (8) to the fully EXTENDED position.7. To adjust the low power setting, turn the adjustment pin (5) counterclockwise to retract rod (8). Retract the rod (8) until the rack setting is decreased to the specified setting.For the correct fuel setting specifications, see the Engine Information Plate or the FUEL SETTING AND RELATED INFORMATION FICHE.8. Replace cover (6) on the variable power actuator (6).
Governor And Variable Power Actuator
1. Variable