105690-0242 ZEXEL 9 420 616 288 BOSCH AUTO;TIMING DEVICE 9420616288 1056900242 1157405242

Information auto;timing device

BOSCH 9 420 616 288 9420616288

ZEXEL 105690-0242 1056900242

ISUZU 1157405242 1157405242

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy AUTO;TIMING DEVICE 105690-0242 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

1.	[1]	156990-3121	AUTO;TIMING DEVICE
1/1.	[1]	156900-9521	FLANGE BUSHING
1/2.	[1]	156901-9121	TIMING-DEVICE HOUSING
1/3.	[2]	156904-0400	ECCENTRIC DISC
1/3.	[2]	156904-0400	ECCENTRIC DISC
1/4.	[2]	156904-0500	ECCENTRIC DISC
1/4.	[2]	156904-0500	ECCENTRIC DISC
1/5.	[2]	156907-3721	PLATE
1/7.	[4]	156908-6900	COILED SPRING
1/7.	[4]	156908-6900	COILED SPRING
1/11.	[1]	156905-1821	CYLINDER
1/12.	[2]	156906-0201	PUMP PLUNGER
1/13.	[2]	156906-0201	PUMP PLUNGER
1/14.	[1]	156902-1721	COVER
1/15.	[6]	156913-3300	BLEEDER SCREW
1/16.	[1]	156913-4820	TIMING RING
1/17.	[1]	156911-0600	BEARING PIN
1/18.	[1]	011004-0820	SET OF NUTS
1/35.	[4]	156913-7300	SHIM
1/35.	[4]	156913-7300	SHIM
2.	[1]	479771-5002	PULSE GENERATOR
3.	[1]	029201-6150	UNION NUT
4.	[1]	139316-0000	PLAIN WASHER D25&16.5T5
5.	[1]	156913-8300	PLATE
6.	[2]	020018-2070	BLEEDER SCREW M8P1.25L20 7T
7.	[2]	014020-8140	PLAIN WASHER D16&8.5T1.2
9.	[1]	479771-5122	PULSE GENERATOR
13.	[1]	156913-4701	CAPSULE
14.	[1]	156914-4521	CAPSULE
15.	[1]	025804-1610	WOODRUFF KEY
16.	[1]	131325-1800	UNION NUT
17.	[1]	029321-4030	LOCKING WASHER

Include in #1:

101606-0092 as AUTOM. ADVANCE MECHANIS

101606-0102

101606-0112

Cross reference number

Zexel num

Bosch num

Firm num

Name

105690-0242
105690-0243

9 420 616 288

1157405242 ISUZU

AUTO;TIMING DEVICE
* K

Information:

Refer to attached Rework Procedure.
SERVICE CLAIM ALLOWANCES
Product smu/age whichever comes first Caterpillar Dealer Suggested Customer Suggested
Parts % Labor Hrs% Parts % Labor Hrs% Parts % Labor Hrs%
*******Group 1*******
0-2000 hrs,
0-12 mo 100.0% 100.0% 0.0% 0.0% 0.0% 0.0%
2001-5000 hrs,
13-18 mo 100.0% 50.0% 0.0% 0.0% 0.0% 50.0%
5001-8000 hrs,
19-24 mo 100.0% 30.0% 0.0% 0.0% 0.0% 70.0%
This is a 4.0-hour job for Group 1
Product smu/age whichever comes first Caterpillar Dealer Suggested Customer Suggested
Parts % Labor Hrs% Parts % Labor Hrs% Parts % Labor Hrs%
*******Group 2*******
0-2000 hrs,
0-12 mo 100.0% 100.0% 0.0% 0.0% 0.0% 0.0%
2001-5000 hrs,
13-18 mo 100.0% 50.0% 0.0% 0.0% 0.0% 50.0%
5001-8000 hrs,
19-24 mo 100.0% 30.0% 0.0% 0.0% 0.0% 70.0%
This is a 4.0-hour job for Group 2
PARTS DISPOSITION
removed java code "affectDisposition"commented on Chints October 12 2006 Chints w.r.t CM000343756-->
Handle the parts in accordance with your Warranty Bulletin on warranty parts handling.
Rework Procedure
For the following units listed remove (6) 207-5248 Injector Rocker Arms, and replace with (6) 278-1365 Injector Rocker Arms.
For proper ?Disassembly & Assembly? instructions of the injector rocker arms please refer to the following Publications in SIS Web. (SENR9832-06 Testing & Adjusting-Finding Top Dead Center Position for No. 1 Piston), (SENR9832-06 Testing & Adjusting-Electronic Unit Injector Adjusting & Setting), and (SENR9832-06 Testing & Adjusting-Engine Valve Lash Inspect/Adjust).
Note: It is important that while installing the 278-1365 Injector Rocker Arms, that the engine is in the proper position (Top Dead Center and 180 degrees out) so the Injector Rocker Arms are properly adjusted and set. It is also important that during the installation of the Injector Rocker Arms that the Exhaust Valve, and Intake Valve lash settings be inspected and if needed re-set to factory specifications.
Note: During the rework process please inspect the 6I-0901 Rocker Arm Shafts for any signs of misalignment of the stud mounting holes, wear, damage, fretting etc. If damage is found to the shaft or if fretting or damage is found with any of the through bolt/stud mounting holes, the shaft is to be replaced, and reported against this service letter as contingent damage.