105952-2562 ZEXEL F 019 Z9E 819 BOSCH ACTUATOR f019z9e819 1059522562

Information actuator

BOSCH F 019 Z9E 819 f019z9e819

ZEXEL 105952-2562 1059522562

Price: query

Buy now
Add to cart Go to cart

Rating:

Buy ACTUATOR 105952-2562 zexel genuine, new aftermarket engine parts with delivery

Scheme ###:

1.	[1]	159560-1601	GOVERNOR HOUSING
2.	[10]	139006-4100	BLEEDER SCREW
3.	[1]	029621-7050	PACKING RING
4.	[1]	159564-0000	COILED SPRING
5.	[1]	159564-4000	SLOTTED WASHER
6.	[1]	159635-8800	SLOTTED WASHER
7.	[1]	159636-3121	CONNECTOR
7B.	[1]	159636-3321	CONNECTOR
7C.	[1]	159636-3521	CONNECTOR
8.	[1]	020105-1240	BLEEDER SCREW
11.	[1]	159579-3022	ACTUATOR
11/2.	[1]	159583-1020	STRAP
11/3.	[1]	159563-1700	LEVER SHAFT
11/4.	[2]	029311-0170	SHIM
11/4.	[2]	029311-0170	SHIM
11/5.	[2]	016500-0710	O-RING
11/5.	[2]	016500-0710	O-RING
11/6.	[2]	014011-0140	PLAIN WASHER
11/6.	[2]	014011-0140	PLAIN WASHER
11/8.	[1]	016010-0940	LOCKING WASHER
11/21.	[1]	159563-6100	CONTROL LEVER
11/22.	[1]	159563-1600	COILED SPRING
11/23.	[1]	159563-1800	BUSHING
11/24.	[1]	014110-8440	LOCKING WASHER D15.4&8.2T2
11/25.	[1]	013030-8140	UNION NUT
11/26.	[1]	159563-1000	FLAT-HEAD SCREW
11/27.	[2]	139006-9800	FLAT-HEAD SCREW
11/27.	[2]	139006-9800	FLAT-HEAD SCREW
11/28.	[2]	013020-6040	UNION NUT
11/28.	[2]	013020-6040	UNION NUT
12.	[2]	020106-4040	BLEEDER SCREW
13.	[1]	159561-0400	GOVERNOR COVER
14.	[4]	139006-9300	BLEEDER SCREW
15.	[2]	139006-9200	BLEEDER SCREW
17.	[1]	159566-4401	GASKET
18.	[1]	154390-0400	GASKET
19.	[1]	154390-0500	GASKET
20.	[1]	153021-6300	CAP
21.	[1]	026524-3040	GASKET
22.	[1]	029731-4680	EYE BOLT
23.	[2]	139514-0300	GASKET D18.6&14.2T1.6
27.	[2]	139006-9400	BLEEDER SCREW
30.	[1]	159584-8100	BRACKET
31.	[2]	020106-1240	BLEEDER SCREW
32.	[1]	159584-6400	CLAMPING BAND
33.	[2]	020106-0840	BLEEDER SCREW
80.	[1]	159584-0000	TOOTHED GEAR
81.	[1]	014111-2420	LOCKING WASHER
82.	[1]	013031-2120	UNION NUT
83.	[1]	025803-1310	WOODRUFF KEY 13 MM
90.	[1]	159584-6322	BRACKET
91.	[2]	010010-2040	BLEEDER SCREW
92.	[2]	014111-0440	LOCKING WASHER
93.	[1]	159584-6400	CLAMPING BAND
94.	[2]	020106-0840	BLEEDER SCREW
900S.	[1]	025803-1310	WOODRUFF KEY 13 MM
901S.	[1]	025803-1610	WOODRUFF KEY 16 MM

Include in #1:

108622-3964 as GOVERNOR

108622-3975

Cross reference number

Zexel num

Bosch num

Firm num

Name

105952-2562

F 019 Z9E 819

ACTUATOR
K 14JD ACTUATOR GOV

Information:

3. Install dowel (5) in governor shaft (6). Install the governor shaft in the carrier as shown. 4. Put the carrier in position on the camshaft. Install the bolts that hold the carrier in place.
Replace shield (7) with a new part any time it is removed.
5. Install shield (7) on the carrier, and use Tool (A) to push the shield against its seat. Use a hammer and punch to stake the metal in two places on the side of the shield 180° 5° apart next to the holes in the shield. 6. Install one race (9), bearing (10), the other race (9), and use Tool (B) to install the ring on riser (8) as shown. 7. Install riser (8) and the spring (overfueling spring) on the governor shaft as shown. 8. Assemble the dashpot as follows:a. Install spring (12) on seat (11). Install seat (13) in spring (12).b. Put spool (14) and ring (15) in position on seat (13). Use Tool (B) to install snap ring (16) to hold them in place. 9. Install dashpot assembly (17) on the governor shaft as shown. 10. Install ring (21) in the lower groove in the governor shaft. Install one sleeve (20), spring (19), the other sleeve (20) and bearing (18) on the governor shaft as shown. Spring (19) is used to put a preload on the thrust bearing on the camshaft in the fuel injection pump housing.11. Use Tool (C) to hold spring (19) under compression. Install ring (22) in the groove in the governor shaft. Remove Tool (C). 12. Put lever (27) in position on governor servo (23). Install pin (24) to hold the lever in place. Use a hammer and chisel to stake the metal four places 90° apart on the outside surface on both legs of the governor servo to hold pin (24) in place.13. Install the O-ring seal on sleeve (25). Install piston (26) and sleeve (25) in the governor servo as shown. 14. Install valve (28) in the governor servo as shown. 15. Install one lockring (32) in the groove near the center of valve (28). Put sleeve (29), spring (broken link spring) (30) and seat (31) in position on valve (28). Install the other lockring (32) to hold the components in place. 16. Put the governor servo in position on the fuel injection pump housing with piston (26) engaged over rack (33). Install the bolts that hold the governor servo in place. The 3306 Engine has two adjustment screws and lock nuts.17. Install torque rise adjustment screw (36) in collar (34) as shown. Install locknut (35) on the screw. 18. Install bolt (38) in block (40) as shown. Install spring (37) on bolt (38) as shown. Put collar (34) in position on bolt (38) with the hole in the collar